Brother CS6000I Sewing Stretch Fabrics and Elastic Tape, Stretch stitching, Elastic attaching

Page 42

SEWING STRETCH FABRICS AND ELASTIC TAPE

Stretch fabrics can be sewn and elastic tape can be attached.

Pattern No.

Stitch Width

Stitch Length

NeedleTwin

FootWalking

Reverse/ Reinforcement Stitching

Pattern

FootPresser

stitches70 model

stitches40 model

[mm (inch.)]

[mm (inch.)]

stitches60 model

stitches50 model

Stitch Name

Application

Auto

Manual

Auto

Manual

Stretch stitch

J

03

03

03

03

Sewing stretch fabrics

1.0

1.0–3.0

2.5

1.0–4.0

Yes

No

Rfc.

*

and decorative stitching

(1/16)

(1/16–1/8)

(3/32)

(1/16–3/16)

( J )

Overcasting on medium

*

3-point

J

05

05

05

05

weight or stretch fabrics,

5.0

1.5–7.0

1.0

0.2–4.0

Yes

No

Rfc.

zigzag stitch

attaching elastic, darn-

(3/16)

(1/16–1/4)

(1/16)

(1/64–3/16)

( J )

ing, etc.

*Rfc.: Reinforcement

Observe the corresponding precautions when performing each of the following stitching operations.

3

Stretch stitching

aAttach zigzag foot “J”.

bSelect stitch .

cSew the fabric without stretching it.

Elastic attaching

When elastic tape is attached to the cuff or waist of a piece of clothing, the finished dimensions will be that of the stretched elastic tape. Therefore, it is necessary that a suitable length of the elastic tape be used.

aPinfabric.the elastic tape to the wrong side of the Pin the elastic tape to the fabric at a few points to make sure that the tape is uniformly positioned on the fabric.

1

2

aElastic tape

bPin

bAttach zigzag foot “J”.

cSelect stitch .

dSew the elastic tape to the fabric while stretching the tape so that it is the same length as the fabric.

While pulling the fabric behind the presser foot with your left hand, pull the fabric at the pin nearest the front of the presser foot with your right hand.

CAUTION

●When sewing, be sure that the needle does not touch any pins, otherwise the needle may bend or break.

41

Image 42

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinLightly hold the end of the upper thread Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the Presser Foot Replacing the presser footMark on the wheel points up. With models Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionBlind HEM Stitching BAttach blind hem foot R CSelect a stitchIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitchingDTrim along the stitches Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersJoining Heirloom stitchingUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216