Brother CS6000I operation manual Patchwork crazy quilt stitching, Piecing

Page 44

dCarefully sew around the edge of the design.

eCut away any fabric that is left outside the stitching.

fRemove the basting, if necessary.

Memo

●Make reinforcing straight stitches at the beginning and the end of stitching.

CAUTION

●Be careful that the needle does not hit a pin during sewing, as the needle can break. You may also be injured.

Patchwork (crazy quilt) stitching

aFold the edge of the top piece of fabric and place it over the lower piece.

bSew the two pieces of fabric together so the pattern spans both pieces.

Piecing

Sewing together two pieces of fabric is called “piecing”. The fabric pieces should be cut with a 6.5 mm (1/4 inch) seam allowance.

Sew a piecing straight stitch 6.5 mm (1/4 inch) from either the right side or the left side of the presser foot.

Baste or pin along the seam allowance of the
afabric that you wish to piece together.
bAttach zigzag foot “J”.
cSelect stitch	or .
	3

dSew with the side of the presser foot aligned with the edge of the fabric.

■For a seam allowance on the right side Align the right side of the presser foot with the

edge of the fabric, and sew using stitch .

1

a6.5 mm (1/4 inch)

■For a seam allowance on the left side

Align the left side of the presser foot with the edge of the fabric, and sew using stitch .

1

a6.5 mm (1/4 inch)

Memo

●To change the width of the seam allowance (the needle position), adjust the stitch width. For details, refer to “Changing the needle position” (page 33).

43

Image 44

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionThreading the Machine Winding the bobbinPass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Needle precautions Replacing the NeedleNeedle types and their uses FabricsChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footGeneral sewing procedure SewingDIfwidth.necessary, adjust the stitch length Selecting stitchingTurn on the sewing machine CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesUsing a free-arm style Sewing thin fabricsSewing stretch fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingUsing the optional quilting guide QuiltingBaste the fabric to be quilted DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogReinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching DTrim along the stitches FagotingScallop stitching Smocking Shell tuck stitchingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Lower Or breaksThread ten Fabric isStitches are SkippedThere is a high Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216