Brother CS6000I operation manual For Users in the UK, EIRE, Malta and Cyprus only

Page 2

FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY

If this machine is fitted with a three-pin non-rewireable BS plug then please read the following.

IMPORTANT

If the available socket outlet is not suitable for the plug supplied with this equipment, it should be cut off and an appropriate three-pin plug fitted. With alternative plugs an approved fuse must be fitted in the plug.

NOTE

The plug served from the main lead must be destroyed as a plug with bared flexible cords is hazardous if engaged in a live socket outlet. In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug. Always replace the fuse cover, never use plugs with the fuse cover omitted.

WARNING

DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE

LETTER ‘E’, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN AND YELLOW.

The wires in this main lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wiring in the main lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or coloured black or blue.

The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or coloured red or brown.

1

Image 2

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching DTrim along the stitches FagotingScallop stitching Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216