Brother CS6000I operation manual Zipper Insertion, Rev. Reverse

Page 41

UTILITY STITCHES ——————————————————————————————————————————————————

ZIPPER INSERTION

You can use the zipper foot to sew different types of zippers, and can easily position it to the right or left side of the needle.

When sewing the right side of the zipper, attach the shank to the left pin of the zipper foot. When sewing the left side of the zipper, attach the shank to the right pin of the zipper foot.

Stitch Name

Straight stitch (center)

 

 

Presser Foot

 

Pattern No.

 

Pattern

 

 

 

 

70 stitches model

60 stitches model

50 stitches model

40 stitches model

 

 

I

01

01

01

01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stitch Width

Stitch Length

 

[mm (inch.)]

[mm (inch.)]

Application

 

 

 

 

 

 

 

 

 

Auto

Manual

Auto

Manual

Attaching zippers, basic

 

 

2.5

0.2–5.0

stitching, and sewing

(3/32)

(1/64–3/16)

gathers or pintucks, etc.

 

 

 

 

 

 

 

 

 

 

 

Twin Needle

Walking Foot

Reverse/ Reinforcement Stitching

Yes

**

Rev.

*

( J )

Yes

 

 

 

 

 

 

 

 

*Rev.: Reverse

**Do not use reverse stitching.

12

3

aZipper foot

bRight pin for sewing the left side of the zipper

cLeft pin for sewing the right side of the zipper

aSelect stitch .

bLower the presser foot lever and fix either the left or right pin of the zipper foot onto the shank.

cFold the edge of the material 2 cm (3/4 inch) and place the zipper under the folded section. Lower the needle into the notch located either on the left or right side of the zipper foot.

CAUTION

Turn the handwheel by hand to make sure the needle does not hit the presser foot before you start sewing. If you choose a different stitch, the needle will hit the presser foot and break the needle. You may also be injured.

dSew from the bottom of the zipper toward the top on both sides. The needle should be positioned on the zipper side of the foot for best results.

eTo sew the opposite side of the zipper, release the foot by pressing the button located at the back of the presser foot, fit the zipper foot on the other side of the zipper and continue sewing using the other side notch.

CAUTION

Make sure the needle does not hit the zipper during sewing. If the needle hits the zipper, the needle may break and you may be injured.

40

Image 41
Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Optional accessories AccessoriesPower supply precautions Using Your Sewing MachineBSet the main power switch to CTo turn off the machine, set the main power switch toChanging the needle stop position Foot controllerWinding the bobbin Threading the MachinePass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverLightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Replacing the Needle Needle precautionsNeedle types and their uses FabricsReplacing the needle Checking the needleCorrect needle Incorrect needleInstalling the needle clamp Twin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footSewing General sewing procedureSelecting stitching DIfwidth.necessary, adjust the stitch lengthTurn on the sewing machine CAttach the presser footBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Sewing reinforcement stitches Thread tensionCorrect tension Upper tension is too tightTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesSewing thin fabrics Using a free-arm styleSewing stretch fabrics Slide the flat bed attachment to the left to release itAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesBasic Stitching When sewing is finished, cut the threadBasic stitching Changing the needle positionIf the needle does not catch the hem fold Blind HEM StitchingBAttach blind hem foot R CSelect a stitch Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingQuilting Using the optional quilting guideBaste the fabric to be quilted DSelect stitch , orGAfter sewing is finished, slide the feed dog Free-motion quiltingTriple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching DTrim along the stitches FagotingScallop stitching Shell tuck stitching SmockingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersUnfold the fabric, and then iron the tucks down to one side JoiningHeirloom stitching Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Remove the bobbin case Troubleshooting Or breaks LowerThread ten Fabric isSkipped Stitches areThere is a high Pitched noise While sewingOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-4216