Brother CS6000I Maintenance, Cleaning the machine surface, Cleaning the bobbin case

Page 58

MAINTENANCE

Simple sewing machine maintenance operations are described below.

Cleaning the machine surface

If the surface of the machine is dirty, lightly soak a cloth in neutral detergent, squeeze it out firmly, and then wipe the surface of the machine. After cleaning it once with a wet cloth, wipe it again with a dry cloth.

CAUTION

●Unplug the power supply cord before cleaning the machine, otherwise injuries or an electric shock may occur.

Cleaning the bobbin case

Sewing performance will suffer if dust collects in the bobbin case; therefore, it should be cleaned periodically.

CAUTION

●Make sure you unplug the machine before you clean it. Otherwise, you may get an electric shock or be injured.

aSwitch the machine off and unplug it.

4

bRaise the needle and the presser foot.

cLoosen the presser-foot screw and the needle

clamp screw to remove the presser-foot holder and the needle.

dGrasp both sides of the needle plate cover, and then slide it toward you to remove the needle plate cover.

aNeedle plate cover

57

Image 58

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Scallop stitching FagotingDTrim along the stitches Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersHeirloom stitching JoiningUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216