Brother CS6000I operation manual Thread take-up lever

Page 18

cPull up the spool pin as far as possible, and then put a spool of thread on this pin.

CAUTION

●If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.

dFeed the upper thread as shown in the figure on the previous page.

eMake sure you guide the thread through the thread take-up lever from right to left.

aThread take-up lever

fPut the thread behind the needle bar thread guide above the needle.

The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.

aNeedle bar thread guide

gThread the needle from front to back and pull out about 5 cm (2 inch) of thread.

a5 cm (2 inch)

Note

● If the thread take-up lever is lowered, the
upper thread cannot be wrapped around the
thread take-up lever. Make sure you raise	1
the presser foot lever and the thread take-up	1

lever before you feed the upper thread.

●If you incorrectly feed the thread you may cause sewing problems.

■Using the needle threader (for models equipped with the needle threader)

CAUTION

●The needle threader can only be used with home sewing machine needles size 75/11- 100/16. Check the table on page 20 for the appropriate needle and thread combinations. If you are using transparent nylon mono- filament thread, you can only use needles in the range of 90/14-100/16.

●You cannot use the needle threader if you are using decorative threads or special needles, such as the twin needle and wing needle.

If you are using those types of threads or needles, thread the eye of the needle by hand. Make sure the main power switch is off when threading the needle by hand.

aFollow steps 1 through 6 of the procedure in “Upper threading” to thread the machine to the needle bar thread guide.

bLower the presser foot lever.

cWhile lowering the needle threader lever, hook the thread onto the guide.

aNeedle holder

bNeedle threader lever

cGuide

17

Image 18

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionPass the thread around the pre-tension disk Threading the MachineWinding the bobbin ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinLightly hold the end of the upper thread Needle types and their uses Needle precautionsReplacing the Needle FabricsCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the Presser Foot Replacing the presser footMark on the wheel points up. With models Attaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder Remove the presser footGeneral sewing procedure SewingTurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser footStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing stretch fabrics Using a free-arm styleSewing thin fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchBasic stitching When sewing is finished, cut the threadBasic Stitching Changing the needle positionBlind HEM Stitching BAttach blind hem foot R CSelect a stitchIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingBaste the fabric to be quilted Using the optional quilting guideQuilting DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogBar tack stitching Reinforcement StitchingTriple stretch stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitchingDTrim along the stitches Sew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersJoining Heirloom stitchingUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case Remove the bobbin case Troubleshooting Thread ten LowerOr breaks Fabric isThere is a high Stitches areSkipped Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216