Brother CS6000I operation manual Sewing with a twin needle, Twin needle threading

Page 24

Sewing with a twin needle

We have designed your machine so you can sew with this needle and two top threads. You can use the same color or two different colors of thread for making decorative stitches.

For details on the stitches that can be sewn with the twin needle, refer to “Stitch settings” (page 52).1

CAUTION

●Use only twin needles that have been made for this machine (part code: 131096-121). Other needles could break, and damage the machine.

●Do not sew with bent needles. The needle could break and injure you.

●You can not use the needle threader to thread the twin needle. Instead, thread the twin needle by hand, from front to back. Using the needle threader may damage the machine.

●When using the twin needle, be sure to select an appropriate stitch, otherwise the needle may break or the machine may be damaged.

●Select a stitch width of 5.0 mm (3/16 inch) or less, otherwise the needle may break or the machine may be damaged.

●After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.

●When using the twin needle, be sure to attach zigzag foot “J”, otherwise the needle may break or the machine may be damaged.

●When changing the sewing direction, be sure to raise the needle before turning the fabric. If the fabric is turned while the needle is lowered, the needle may bend or break.

■Twin needle threading

aAttach the twin needle.

Attach the twin needle in the same way as a single needle (page 21).

bAttach the extra spool pin.

Put the extra spool pin in the hole on the top of the machine. Put the second spool of thread onto the extra spool pin.

aFirst spool

bSecond spool

cUse the thread from the first spool to thread the machine to the needle bar thread guide. The path for threading the machine to the needle bar thread guide is the same as for normally threading the machine (for a single needle). See page 17 for more details.

dThread the left needle from front to back.

eUse the thread from the second spool to thread the machine to the thread take-up lever.

The path for threading the machine to the thread take-up lever is the same as for normally threading the machine (for a single needle). See page 17 for more details.

fThread the right needle from front to back. Do not pass the thread behind the needle bar thread guide.

aLeft needle thread passes through the needle bar thread guide.

bRight needle thread passes in front of the needle bar thread guide.

cNeedle bar thread guide

Note

Models equipped with a needle threader

●You cannot use the needle threader to thread the twin needle. Instead, thread the twin needle by hand, from front to back. Using the needle threader may damage the machine.

CAUTION

●When using the twin needle, be sure to attach zigzag foot “J”, otherwise the needle may break or the machine may be damaged.

23

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For a longer service life For safe operationContents Utility Stitches Names of Machine Parts and Their Functions Main partsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionThreading the Machine Winding the bobbinPass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightLower threading Actual size 11.5mm 7/16 inch This modelRight side see arrow b until the cover clicks into place For models equipped with the quick-set bobbinUpper threading Thread take-up lever DFully lower the needle threader lever Catch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinLightly hold the end of the upper thread Needle precautions Replacing the NeedleNeedle types and their uses FabricsChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Sewing with a twin needle Twin needle threadingReplacing the Presser Foot Replacing the presser footMark on the wheel points up. With models Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footGeneral sewing procedure SewingDIfwidth.necessary, adjust the stitch length Selecting stitchingTurn on the sewing machine CAttach the presser footStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesUsing a free-arm style Sewing thin fabricsSewing stretch fabrics Slide the flat bed attachment to the left to release itOvercasting Stitches Attach overcasting foot G or zigzag foot J Select a stitchWhen sewing is finished, cut the thread Basic StitchingBasic stitching Changing the needle positionBlind HEM Stitching BAttach blind hem foot R CSelect a stitchIf the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onSize of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsCAttach presser foot M ESelect a stitch With stitch Select stitchZipper Insertion Rev. ReverseSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching PiecingUsing the optional quilting guide QuiltingBaste the fabric to be quilted DSelect stitch , orFree-motion quilting GAfter sewing is finished, slide the feed dogReinforcement Stitching Triple stretch stitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingOnce sewing is completed, Pullpossible.down the buttonhole lever as far asDecorative Stitching Fagoting Scallop stitchingDTrim along the stitches Smocking Shell tuck stitchingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersJoining Heirloom stitchingUnfold the fabric, and then iron the tucks down to one side Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case Remove the bobbin case Troubleshooting Lower Or breaksThread ten Fabric isStitches are SkippedThere is a high Pitched noise While sewingError Messages Operation beep for models equipped with the operation beepIndex Numerics30, 32 English 885-S33/S34/S36/S37 XC8835-4216
Top Page Image Contents