Brother CS6000I operation manual Replacing the Presser Foot, Replacing the presser foot

Page 25

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

REPLACING THE PRESSER FOOT

CAUTION

●Always turn off the power before you change the presser foot. If you leave the power on and step on the controller, the machine will start and you may be injured.

●Always use the correct presser foot for the stitch pattern you have chosen. If you use the wrong presser foot, the needle may strike the presser foot and bend or break, and may cause injury.

●Only use presser feet that have been designed to be used with this machine. Using other any presser feet may cause an accident or injury.

Replacing the presser foot

Replace the presser foot as described below.

aRaise the needle by turning the handwheel toward you (counterclockwise) so that the

mark on the wheel points up. (With models

equipped with (needle position button), raise the needle by pressing once or twice.)

or

a Mark

b Needle position button

bIfturntheitsewingoff. machine has been turned on,

CAUTION

●Before replacing the presser foot, be sure to turn off the sewing machine, otherwise injuries may occur if the foot controller or the start/stop button is accidentally pressed and the machine starts sewing.

cRaise the presser foot lever.

dPress the black button at the back of the presser foot holder to release the presser foot.

aBlack button

bPresser foot holder

ePlace a different presser foot below the holder so that the presser foot pin is aligned with the shank in the holder.

Position the presser foot so the letter indicating the presser foot type (J, A, etc.) is positioned to be read.

aPresser foot holder

bShank

cPin

Note

●The presser foot to be used with each stitch appears in the LCD. To select a stitch, refer to “Selecting stitching” (page 27).

aPresser foot lever

24

Image 25

Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Optional accessories AccessoriesPower supply precautions Using Your Sewing MachineBSet the main power switch to CTo turn off the machine, set the main power switch toChanging the needle stop position Foot controllerWinding the bobbin Threading the MachinePass the thread around the pre-tension disk ETurn on the sewing machineGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Replacing the Needle Needle precautionsNeedle types and their uses FabricsReplacing the needle Checking the needleCorrect needle Incorrect needleInstalling the needle clamp Twin needle threading Sewing with a twin needleReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Removing the presser foot holder Removing the presser foot holderAttaching the presser foot holder Remove the presser footSewing General sewing procedureSelecting stitching DIfwidth.necessary, adjust the stitch lengthTurn on the sewing machine CAttach the presser footOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Sewing reinforcement stitches Thread tensionCorrect tension Upper tension is too tightTrial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesSewing thin fabrics Using a free-arm styleSewing stretch fabrics Slide the flat bed attachment to the left to release itAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesBasic Stitching When sewing is finished, cut the threadBasic stitching Changing the needle positionBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingQuilting Using the optional quilting guideBaste the fabric to be quilted DSelect stitch , orGAfter sewing is finished, slide the feed dog Free-motion quiltingTriple stretch stitching Reinforcement StitchingBar tack stitching Attach zigzag foot J Select stitch Start sewingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching Scallop stitching FagotingDTrim along the stitches Shell tuck stitching SmockingSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersHeirloom stitching JoiningUnfold the fabric, and then iron the tucks down to one side Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin case Troubleshooting Or breaks LowerThread ten Fabric isSkipped Stitches areThere is a high Pitched noise While sewingOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-4216