Brother CS6000I operation manual Needle and presser foot section, Operation buttons

Page 7

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

Needle and presser foot section

aButtonhole lever

Lower the buttonhole lever when sewing buttonholes and bar tacks.

bNeedle threader (for models equipped with the needle threader) (page 17)

cPresser foot holder

The presser foot is installed onto the presser foot holder.

dPresser foot holder screw

Use the presser foot holder screw to hold the presser foot holder in place.

ePresser foot

The presser foot applies pressure consistently on the fabric as the sewing takes place. Attach the appropriate presser foot for the selected stitching.

fFeed dogs

The feed dogs feed the fabric in the sewing direction.

gQuick-set bobbin (for models equipped with the quick- set bobbin)

You can start sewing without pulling up the bobbin thread.

hBobbin cover

Open the bobbin cover to set the bobbin.

iNeedle plate

The needle plate is marked with guides for sewing straight seams.

jNeedle bar thread guide

Pass the upper thread through the needle bar thread guide.

kNeedle clamp screw

Use the needle clamp screw to hold the needle in place.

Operation buttons

The operation buttons help you to easily perform various basic sewing machine operations. The operation buttons differ depending on the sewing machine model.

aPresser foot lever

Raise and lower the presser foot lever to raise and lower the presser foot.

bReverse/reinforcement stitch button

Press the reverse/reinforcement stitch button to sew reverse stitches. Reverse stitches are sewn by keeping the button pressed down to sew in the opposite direction. For details, refer to “Sewing reinforcement stitches” (page 29).

■Buttons provided on some models

c Start/stop button (for models equipped with the start/stop button)

Press the start/stop button to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is depressed. When sewing is stopped, the needle is lowered in the fabric. For details, refer to “Starting to sew” (page 28).

d Needle position button (for models equipped with the needle position button)

Press the needle position button to raise or lower the needle. Pressing the button twice sews one stitch.

eSewing speed controller (for models equipped with the sewing speed controller)

Slide the sewing speed controller to adjust the sewing speed.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Computerized Sewing Machine For Users in the UK, EIRE, Malta and Cyprus only For safe operation For a longer service lifeContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsOperation buttons Needle and presser foot sectionButtons provided on some models Flat bed attachment Operation panelASlideopen theit. flat bed attachment to the left to Optional accessories AccessoriesCTo turn off the machine, set the main power switch to Using Your Sewing MachinePower supply precautions BSet the main power switch toChanging the needle stop position Foot controllerETurn on the sewing machine Threading the MachineWinding the bobbin Pass the thread around the pre-tension diskGTrim the excess thread above the bobbin CSlide the bobbin winder shaft to the right For models equipped with the fast bobbin winding systemActual size 11.5mm 7/16 inch This model Lower threadingFor models equipped with the quick-set bobbin Right side see arrow b until the cover clicks into placeUpper threading Thread take-up lever Catch the thread on the hook as shown below DFully lower the needle threader leverFor models equipped with the quick-set bobbin Drawing up the lower threadLightly hold the end of the upper thread Fabrics Needle precautionsReplacing the Needle Needle types and their usesIncorrect needle Checking the needleReplacing the needle Correct needleInstalling the needle clamp Twin needle threading Sewing with a twin needleReplacing the presser foot Replacing the Presser FootMark on the wheel points up. With models Remove the presser foot Removing the presser foot holderRemoving the presser foot holder Attaching the presser foot holderSewing General sewing procedureCAttach the presser foot DIfwidth.necessary, adjust the stitch lengthSelecting stitching Turn on the sewing machineOn the wheel points up. With models equipped Starting to sewBRaise the presser foot lever Upper tension is too tight Thread tensionSewing reinforcement stitches Correct tensionSewing curves Useful Sewing TipsTrial sewing Changing the sewing directionSlide the flat bed attachment to the left to release it Using a free-arm styleSewing thin fabrics Sewing stretch fabricsAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesChanging the needle position When sewing is finished, cut the threadBasic Stitching Basic stitchingBAttach blind hem foot R CSelect a stitch Blind HEM StitchingIf the needle does not catch the hem fold Buttonholes can be sewn and buttons can be sewn on Buttonhole SewingIf the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingCAttach presser foot M With stitch Select stitch ESelect a stitchRev. Reverse Zipper InsertionStretch stitching Sewing Stretch Fabrics and Elastic TapeElastic attaching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Patchwork crazy quilt stitchingDSelect stitch , or Using the optional quilting guideQuilting Baste the fabric to be quiltedGAfter sewing is finished, slide the feed dog Free-motion quiltingAttach zigzag foot J Select stitch Start sewing Reinforcement StitchingTriple stretch stitching Bar tack stitchingPullpossible.down the buttonhole lever as far as Once sewing is completed,Decorative Stitching Scallop stitching FagotingDTrim along the stitches DPull the bobbin threads to create gathers SmockingShell tuck stitching Sew parallel stitching at intervals of 1 cm 3/8 inchHeirloom stitching JoiningUnfold the fabric, and then iron the tucks down to one side Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the machine surface MaintenanceCleaning the bobbin case Remove the bobbin case Troubleshooting Fabric is LowerOr breaks Thread tenPitched noise While sewing Stitches areSkipped There is a highOperation beep for models equipped with the operation beep Error MessagesNumerics Index30, 32 English 885-S33/S34/S36/S37 XC8835-4216
Top Page Image Contents