Bradley Smoker MG-2/BIR3 installation instructions Troubleshooting BIR3 Components

Page 16

Express® Lavatory System - MG Series with Battery Infrared Control

 

MG-2/BIR3

Installation Instructions

Troubleshooting BIR3 Components

CAUTION: Turn off water supplies to unit before troubleshooting.

Problem:

An individual operating station drips and fails to shut off.

Cause:

There is debris trapped between the diaphragm and the valve seat.

Solution:

Remove debris between diaphragm and the valve seat.

Disconnect the plug from the battery to the circuit board of the problem valve. Remove the three #8 Phillips-head screws that hold the solenoid valve assembly together. Be careful not to lose the armature or spring (see Figure 13 on page 17). Remove the diaphragm. Remove any particles that are trapped between the diaphragm and the valve seat. Rinse off the diaphragm and inspect for damage. Make sure the center orifice and both small side orifices are open. Reassemble in reverse order, being careful not to overtighten the Phillips-head screws or you may crack the plastic valve body. Tighten until the armature plate makes contact with the plastic body. Reconnect the battery plug per diagram on page 11. Turn on water supplies to the unit.

Problem:

An individual operating station fails to turn on or off.

Cause:

A dead or faulty battery.

Solution:

Test the station to determine cause and replace battery if required.

Disconnect the plug from the battery to the circuit board of the problem valve. Disconnect the plug from the battery to the circuit board of an adjacent valve. Connect the battery plug from the adjacent working valve to the problem valve. Wait for ten seconds. Activate the problem station’s sensor ten times. The station should turn on. If the station turns on, and cycles normally, replace the battery.

Cause:

Faulty sensor eyes.

Solution:

Test station to determine cause; replace sensor eyes if

required.

 

Disconnect the sensor cable from the circuit board of the problem valve. Disconnect the sensor cable from the circuit board of an adjacent working valve. Connect the sensor cable from the adjacent working valve to the problem valve. Activate the problem station’s sensor. The station should turn on. If the station turns on and cycles normally, replace the sensor eyes.

Cause:

Faulty solenoid valve.

Solution:

Test station to determine cause; replace solenoid valve if

 

required.

Remove the screw, circuit board and standoff from the problem valve. Remove the battery holder. With a good working battery, briefly contact the solenoid valve directly with the battery as shown in Figure 12a. The contact should cause the valve to open. With the battery holder removed, briefly contact the solenoid valve with the battery in the position shown in Figure 12b. This should cause the valve to close. If the valve does not operate when directly contacted with a good battery, and the solenoid valve has already been cleaned as outlined at the beginning of this troubleshooting section, replace the solenoid valve.

If problems persist:

Pass your hand in front of the problem station, while at the same time looking to see if the indicator light on the circuit board flashes (the indicator light is located near the hole in the circuit board where the standoff is mounted). If it does not flash, and the battery and sensor eyes have already been tested as outlined above, the problem may be with the circuit board. Make a note of the numbers printed on the circuit board, then contact your Bradley representative for assistance.

Figure 12a

OPEN VALVE

Figure 12b

CLOSED VALVE

16

8/23/07

Bradley Corporation • 215-1510 Rev. D; ECN 07-815

Image 16
Contents Installation Instructions Table of ContentsPre-Installation Information MG-2/BIR3 Express Lavatory System Dimensions Dimensions Installation Instructions Rough in supplies and optional hot water heater23/07 Bradley Corporation 215-1510 Rev. D ECN Rough in wall anchors Mount frame to wall Install bowl assembly Do not overtightenHot Connecting electrical and supply tubing Counterclockwise to increaseCleaning and Maintenance Instructions Terreon and panel maintenanceStainless Steel Access Panel cleaning Terreon Bowl, Sprayhead and Pedestal End Cap cleaningAssembly of Components Other replacement partsSensor assembly and solenoid valve access Infrared Window Sprayhead Body NUT Troubleshooting BIR3 Components Solution Remove debris between diaphragm and the valve seatSolenoid Valve S07-072 closed body and S07-072A thru body Problem Limited water flow Thermostatic Mixing Valve Maintenance and TroubleshootingProblem External leaks in the system Vernatherm Thermostatic Mixing Valve S01-524 Repair Kit S65-259