Electrolux Over The Range Microwave Oven installation instructions C5. Mount the Microwave Oven

Page 20

Installation Instructions

6. Place the blower unit back into the opening.

AFTER: Fan Blade

Openings Facing Back

End A

End B

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.

NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.

7. Secure the blower unit to the microwave with the screw.

Blower-Plate

Back of

From the Mounting

Microwave

Plate screw

8. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven.

Adaptor

Back of

Microwave

 

Guide

Guide

From Blower motor screw

 

(after attached the exhaust adaptor)

Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely.

C5. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1. Lift microwave, tilt it forward, and hook slots at back bottom edge

onto four lower tabs of mounting plate.

2. Rotate front of oven up against cabinet bottom

3. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Installation Instructions Before YOU BeginContents Important Safety Instructions Electrical RequirementsHood Exhaust Outside TOP Exhaust Example onlyOutside Back Exhaust Example only Duct Pieces Equivalent Number Length UsedMaximum duct length Exhaust connectionDamage SHIPMENT/ Installation Parts IncludedHardware Packet Additional PartsTools YOU will Need Mounting SpaceMicrowave Must be Connected to AT Least ONE Wall Stud Placement of the Mounting PlateFinding the Wall Studs Determining Wall Plate Location Under Your Cabinet Microwave Must be LevelHole B Horizontal Line Aligning the Wall PlateHorizontal Line Recirculating NON-VENTED Ductless Outside TOP Exhaust Vertical DuctOutside Back Exhaust Horizontal Duct SeeA1. Attach the Mounting Plate to the Wall To use toggle boltsInstall this Microwave Oven A3. Mount the Microwave OvenInstallation Overview B1. Attach the Mounting PlateTo the Wall To help tighten the boltsBlower plate to Microwave B3. Adapting Microwave Blower for Outside TOP ExhaustRemove and save Lift up Screw that holds B5. Mount the Microwave Oven Onto four lower tabs of mounting plateB6. Adjust the Exhaust Adaptor B7. Connecting DuctworkB5. Mount the Microwave Oven Attach the microwave oven to the top cabinetPlate to a wall stud C1. Preparing the Rear WallFor Outside Back Exhaust C2. Attach the Mounting Plate To the WallC3. USE TOP Cabinet Template For Preparation of TOP CabinetSecure the blower unit to the microwave with the screw C5. Mount the Microwave OvenPlace the blower unit back into the opening C5. Mount the Microwave Oven Before YOU USE Your Microwave
Top Page Image Contents