Electrolux Over The Range Microwave Oven C2. Attach the Mounting Plate, To the Wall

Page 19

Installation Instructions

C2. ATTACH THE MOUNTING PLATE

C4. ADAPTING MICROWAVE BLOWER

TO THE WALL (cont.)

FOR OUTSIDE BACK EXHAUST

To use toggle bolts:

1. Remove and save screw that holds blower Plate

 

Spacing for Toggles More

to microwave.

 

 

 

Blower motor

 

 

 

Than Wall Thickness

 

 

 

screw.

2. Lift up the Blower Plate.

 

Toggle Wings

Mounting

 

Toggle

 

Blower Motor

 

Plate

Bolt

 

 

 

 

 

Back of

 

 

 

 

Microwave

 

 

Wall

 

 

 

 

Bolt End

 

Blower Motor

 

 

 

 

 

3. Place the mounting plate against the wall and

 

Screw

 

3. Carefully pull out the blower unit. The wires will

insert the toggle wings into the holes in the wall to

extend far enough to allow you to adjust the

mount the plate.

blower unit.

 

 

NOTE: Before tightening toggle bolts and wood

 

 

BEFORE: Fan Blade

 

End B

screw, make sure to coincide bottom line of the

Openings Facing Forward

 

Mounting plate with Horizontal line of “Rear wall

 

 

 

Template” and then the Mounting plate is properly

 

 

 

centered under the cabinet.

 

 

 

CAUTION: Be careful to avoid pinching fingers

End A

 

 

between the back of the mounting plate and the wall.

 

 

 

 

 

4. Tighten all bolts. Pull the plate away from the wall

 

 

 

to help tighten the bolts.

CAUTION: Do not touch blade of blower to prevent

 

 

 

 

cracking and breaking. Hold outer case when the

C3. USE TOP CABINET TEMPLATE

blower is removed and re-installed.

 

4. Remove “Parts “A” with Nipper or Scissors

 

FOR PREPARATION OF TOP

 

 

 

 

CABINET

 

 

 

You need to drill holes for the top support screws and

 

Knockouts

 

a hole large enough for the power cord to fit through.

 

 

Parts”A”

5. Rotate blower unit counterclockwise 180°.

Before Rotation

After Rotation

 

• Read the instructions on the TOP CABINET

 

TEMPLATE.

 

• Tape it underneath the top cabinet.

Back of

• Drill the holes, following the instructions on the

Microwave

Back of

TOP CABINET TEMPLATE.

Microwave

CAUTION: Wear safety goggles when drilling holes in

 

the cabinet bottom.

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Before YOU Begin Installation InstructionsContents Electrical Requirements Important Safety InstructionsDuct Pieces Equivalent Number Length Used Hood ExhaustOutside TOP Exhaust Example only Outside Back Exhaust Example onlyExhaust connection Maximum duct lengthAdditional Parts Damage SHIPMENT/ InstallationParts Included Hardware PacketMounting Space Tools YOU will NeedFinding the Wall Studs Placement of the Mounting PlateMicrowave Must be Connected to AT Least ONE Wall Stud Microwave Must be Level Determining Wall Plate Location Under Your CabinetHorizontal Line Aligning the Wall PlateHole B Horizontal Line See Recirculating NON-VENTED DuctlessOutside TOP Exhaust Vertical Duct Outside Back Exhaust Horizontal DuctTo use toggle bolts A1. Attach the Mounting Plate to the WallA3. Mount the Microwave Oven Install this Microwave OvenTo help tighten the bolts Installation OverviewB1. Attach the Mounting Plate To the WallRemove and save Lift up Screw that holds B3. Adapting Microwave Blower for Outside TOP ExhaustBlower plate to Microwave Onto four lower tabs of mounting plate B5. Mount the Microwave OvenAttach the microwave oven to the top cabinet B6. Adjust the Exhaust AdaptorB7. Connecting Ductwork B5. Mount the Microwave OvenFor Outside Back Exhaust C1. Preparing the Rear WallPlate to a wall stud For Preparation of TOP Cabinet C2. Attach the Mounting PlateTo the Wall C3. USE TOP Cabinet TemplatePlace the blower unit back into the opening C5. Mount the Microwave OvenSecure the blower unit to the microwave with the screw C5. Mount the Microwave Oven Before YOU USE Your Microwave
Top Page Image Contents