Electrolux Over The Range Microwave Oven installation instructions B5. Mount the Microwave Oven

Page 16

Installation Instructions

AFTER: Fan Blade Openings

Facing Upward

5. Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched.

6. Secure blower unit to microwave with the screw.

B4. INSTALLATION PROCEDURE FOR EXHAUST ADAPTOR AND PROPER DAMPER OPERATION CHECK

1. Remove and save screw from the panel-outer

Exhaust Adaptor and Damper is shipped after being assembled to the filler-upper.

2. Slide exhaust adaptor following the instructions show in diagram.

3. Make sure tape securing damper is removed and damper pivots easily before mounting microwave.

4. Lift damper and Re-screw at same location as (1).

•You will need to make adjustments to assure proper alignment with your house exhaust duct after the microwave is installed.

B5. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord.

1. Lift microwave, tilt it forward, and hook slots at back bottom edge

onto four lower tabs of mounting plate.

2. Rotate front of oven up against cabinet bottom

3. Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installation Instructions Before YOU BeginContents Important Safety Instructions Electrical RequirementsHood Exhaust Outside TOP Exhaust Example onlyOutside Back Exhaust Example only Duct Pieces Equivalent Number Length UsedMaximum duct length Exhaust connectionDamage SHIPMENT/ Installation Parts IncludedHardware Packet Additional PartsTools YOU will Need Mounting SpaceFinding the Wall Studs Placement of the Mounting PlateMicrowave Must be Connected to AT Least ONE Wall Stud Determining Wall Plate Location Under Your Cabinet Microwave Must be LevelHorizontal Line Aligning the Wall PlateHole B Horizontal Line Recirculating NON-VENTED Ductless Outside TOP Exhaust Vertical DuctOutside Back Exhaust Horizontal Duct SeeA1. Attach the Mounting Plate to the Wall To use toggle boltsInstall this Microwave Oven A3. Mount the Microwave OvenInstallation Overview B1. Attach the Mounting PlateTo the Wall To help tighten the boltsRemove and save Lift up Screw that holds B3. Adapting Microwave Blower for Outside TOP ExhaustBlower plate to Microwave B5. Mount the Microwave Oven Onto four lower tabs of mounting plateB6. Adjust the Exhaust Adaptor B7. Connecting DuctworkB5. Mount the Microwave Oven Attach the microwave oven to the top cabinetFor Outside Back Exhaust C1. Preparing the Rear WallPlate to a wall stud C2. Attach the Mounting Plate To the WallC3. USE TOP Cabinet Template For Preparation of TOP CabinetPlace the blower unit back into the opening C5. Mount the Microwave OvenSecure the blower unit to the microwave with the screw C5. Mount the Microwave Oven Before YOU USE Your Microwave
Top Page Image Contents