Electrolux Over The Range Microwave Oven Important Safety Instructions, Electrical Requirements

Page 3

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electrical requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.

CAUTION: For personal safety, remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury.

CAUTION: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this 59 pound product, plus additional oven loads of up to 50 pounds or a total weight of 109 pounds.

CAUTION: For personal safety, this product cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal safety, it is recommended that two people install this product.

IMPORTANT–PLEASE READ CAREFULLY. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK.

You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is very important to have it replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 14.5 amps and 1.6 kilowatts.

This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

Insure proper

Insure proper

ground existsts

before use

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Before YOU Begin Installation InstructionsContents Electrical Requirements Important Safety InstructionsDuct Pieces Equivalent Number Length Used Hood ExhaustOutside TOP Exhaust Example only Outside Back Exhaust Example onlyExhaust connection Maximum duct lengthAdditional Parts Damage SHIPMENT/ InstallationParts Included Hardware PacketMounting Space Tools YOU will NeedPlacement of the Mounting Plate Finding the Wall StudsMicrowave Must be Connected to AT Least ONE Wall Stud Microwave Must be Level Determining Wall Plate Location Under Your CabinetAligning the Wall Plate Horizontal LineHole B Horizontal Line See Recirculating NON-VENTED DuctlessOutside TOP Exhaust Vertical Duct Outside Back Exhaust Horizontal DuctTo use toggle bolts A1. Attach the Mounting Plate to the WallA3. Mount the Microwave Oven Install this Microwave OvenTo help tighten the bolts Installation OverviewB1. Attach the Mounting Plate To the WallB3. Adapting Microwave Blower for Outside TOP Exhaust Remove and save Lift up Screw that holdsBlower plate to Microwave Onto four lower tabs of mounting plate B5. Mount the Microwave OvenAttach the microwave oven to the top cabinet B6. Adjust the Exhaust AdaptorB7. Connecting Ductwork B5. Mount the Microwave OvenC1. Preparing the Rear Wall For Outside Back ExhaustPlate to a wall stud For Preparation of TOP Cabinet C2. Attach the Mounting PlateTo the Wall C3. USE TOP Cabinet TemplateC5. Mount the Microwave Oven Place the blower unit back into the openingSecure the blower unit to the microwave with the screw C5. Mount the Microwave Oven Before YOU USE Your Microwave
Top Page Image Contents