KitchenAid Overlay Model Beverage Center manual InstallCustom Overlay Frame, Clean Before Using

Page 6

■Dispose of/recycle all packaging materials.

When Moving Your Beverage Center:

Your beverage center is heavy. When moving the appliance for service, be sure to protect the floor. Always pull the appliance straight out when moving it. Do not wiggle or “walk” the appliance when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your beverage center before using it. See the cleaning instructions in “Beverage Center Care.”

3.Open the door. Lift the front of the door up, pulling straight out to remove as shown.

InstallCustom Overlay Frame

IMPORTANT:

■Create custom overlay frame according to the specifications in the “Custom Overlay Frame” section.

■KitchenAid is not responsible for the removal or addition of decorative frames that would prevent the appliance from being serviced.

Remove the Door

IMPORTANT: Do not remove the grease from the washer, top spacer or top hinge pin. Be sure to set aside the top hinge, top spacer and washer for later use.

1.Using a Phillips screwdriver, remove the three screws from the top hinge. Remove the top hinge.

A

B

C

D

E

A. Screws (3)

B. Top hinge

C.Washer

D.Top spacer

E.Door

2.Remove the three screws from the top spacer. Remove the top spacer and washer.

Attach the Overlay Frame

NOTE: If the overlay hooks are not installed, see “Custom Overlay Frame” for overlay hook locations.

1.Position the overlay frame ¹⁄₂" (1.27 cm) higher than the door. Be sure to position the overlay hooks to the pilot holes.

2.Insert the overlay hooks into the top of the holes in the door. Push against the overlay frame to force the overlay hooks deeper into the door. Pull the overlay frame straight down to secure the overlay hooks to the door.

3.Using a Phillips screwdriver, attach the overlay plates to the bottom of the overlay frame and door as shown.

A B C D

A. Overlay frame

B.Door

C.Overlay plates (2)

D.Round-head screws (8)

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Beverage Center Table of Contents ÍndiceTable DES Matières Beverage Center Safety Before You Throw Away Your Old Refrigerated ApplianceInstallation Instructions Toolsand PartsCustom OverlayFrame Unpack the Beverage Center Electrical RequirementsLocation Requirements Recommended grounding methodRemove the Door InstallCustom Overlay FrameClean Before Using Attach the Overlay FrameInstall the Door DoorClosingDoor Closing Base Grille Usingthe ControlBeverage Center USE Normal SoundsBeverage/WineRacks Stockingthe Beverage CenterLighting theBeverage Center Changing the Light Bulb CleaningBeverage Center Care Vacation and MovingCareTroubleshooting U.S.A Assistance or ServiceAccessories CanadaItems Kitchenaid will not PAY for Kitchenaid Refrigerator WarrantyONE Year Limited Warranty Disclaimer of Implied Warranties Limitation of RemediesSeguridad DEL Refrigerador Para Bebidas Antes de descartar su viejo aparato refrigeradoInstrucciones DE Instalación Piezas y herramientasMarcorecubierto a la medida Método de conexión a tierra recomendado Requisitosde ubicaciónRequisitoseléctricos Vista superiorCómo quitar los materiales de empaque Desempaque del refrigerador para bebidasCómo quitar la puerta Limpieza antes del usoCómo fijar el marco recubierto Cómo instalar la puertaSonidosnormales USO DEL Refrigerador Para BebidasCómocerrar la puerta Rejilla de la base Cómo cerrar la puerta Quite la rejilla de la baseUsodel control Portabebidas/portabotellasCómoiluminar el refrigerador para bebidas Cuidado DEL Refrigerador Para BebidasCómo almacenar en el refrigerador Para bebidas LimpiezaPara cambiar el foco Cómocambiar el focoCuidadodurante las vacaciones y mudanzas VacacionesLas luces no funcionan Solución DE ProblemasParece que el motor funciona excesivamente La temperatura está demasiado calienteHay acumulación de humedad en el interior Es difícil abrir la puertaLa puerta no cierra completamente En Canadá Ayuda O Servicio TécnicoEn los EE.UU AccesoriosKitchenaid no Pagará POR LOS Siguientes Artículos Garantía DEL Refrigerador DE KitchenaidGarantía Limitada DE UN AÑO Exclusión DE Garantías Implícitas Limitación DE RecursosSécurité DU Réfrigérateur Pour Boissons Avant de jeter votre vieil appareil réfrigéréInstructions D’INSTALLATION Outillage etpiècesCadre décoratif personnalisé Spécificationsélectriques Exigences demplacementMéthode recommandée de mise à la terre Vue supérieureEnlèvement des matériaux demballage Installation du cadre décoratif personnaliséDéballage du réfrigérateur pour boissons Nettoyage avant utilisationInstallation de la porte Fixation du cadre décoratifFermeture de la porte Grille de la base Réinstallation de la grille de la baseUtilisation DU Réfrigérateur Pour Boissons Sons normauxUtilisation de la commande Grillespourle remisage des Boissons et du vinÉclairage du réfrigérateur pour boissons Entretien DU Réfrigérateur Pour BoissonsStockage dans le réfrigérateurpourboissons NettoyageVacances Changement de lampoule déclairageChangement de lampoule DéménagementDépannage Les ampoules ne fonctionnent pasLe moteur semble fonctionner excessivement La porte est difficile à ouvrir La température est trop élevéeIl existe une accumulation dhumidité à lintérieur La porte ne ferme pas complètementAux États-Unis Assistance OU ServiceAccessoires Au CanadaGarantie DU Réfrigérateur Kitchenaid Garantie Limitée DE UN ANKitchenaid NE Prendra PAS EN Charge 2300277 All rights reserved

Overlay Model Beverage Center specifications

The KitchenAid Overlay Model Beverage Center is the ultimate solution for beverage storage and organization, seamlessly blending functionality and style within your kitchen. This appliance is designed to provide a dedicated space for everything from chilled wines to refreshing sodas, all while maintaining the aesthetic coherence with your kitchen cabinetry thanks to its customizable overlay panel.

One of the main features that sets the KitchenAid Overlay Model apart is its impressive storage capacity. With adjustable shelves, this beverage center can accommodate a variety of bottle sizes and shapes, from standard wine bottles to larger craft beer cans. The glass door not only offers visibility into the contents but also allows for easy access, making it convenient to grab your favorite drink on the go. The interior LED lighting enhances the visibility, illuminating the beverages while minimizing energy consumption.

Temperature control is another standout characteristic of the KitchenAid Overlay Model Beverage Center. Equipped with a sophisticated temperature management system, it ensures that your drinks are stored at optimal temperatures. Users can set two separate temperature zones, making it perfect for keeping wines at the ideal serving temperature while simultaneously chilling other beverages.

The appliance is engineered with a quiet operation technology that maintains a peaceful kitchen ambiance, allowing you to enjoy a tranquil environment without the distraction of unnecessary noise. Additionally, the unit features a door alarm that alerts you if the door is left ajar, preventing fluctuations in temperature that could compromise your beverage inventory.

In terms of design, the KitchenAid Overlay Model Beverage Center is tailored to integrate seamlessly with your existing kitchen décor. The sleek finish and customizable panel options allow homeowners to match the beverage center beautifully with their cabinetry, creating a cohesive and sophisticated look.

Overall, the KitchenAid Overlay Model Beverage Center embodies a blend of stylish design, innovative technologies, and practical features. With its ample storage capacity, precise temperature controls, and quiet operation, it makes a perfect addition to any kitchen or entertaining space, ensuring your beverages are always perfectly chilled and ready to serve.
Top Page Image Contents