KitchenAid KBRS20ETBL manual Factory Trim Kit on some models

Page 13

Factory Trim Kit (on some models)

There may be an occasion when you will need to remove the factory-installed trim kit, such as moving the refrigerator to a new home or installing custom-made decorator panels. Please read all instructions before removing the trim kit and decorator panels.

A

B

C

A. 2¹⁄₂" (6.35 cm) Clearance

B. Raised decorator panel

C. Raised drawer panel

Remove the Door Panel

IMPORTANT:

Door must be removed from refrigerator before removing handle.

Top trim must be removed from refrigerator before removing door panel.

1.Remove the refrigerator handle:

Using a Phillips screwdriver, remove the top door cap.

Tap the bottom edge of refrigerator door handle upward with a rubber mallet.

The handle will slide up approximately ³⁄₄" (19.05 mm) and release from door.

2.Remove the door panel:

Slide out decorator panel and filler board.

Store panel and filler board in such a manner as to avoid scratching.

Replace the Door Panel

1.Replace the refrigerator door panel:

Slide the ¹⁄₄" (6.35 mm), maximum thickness, decorator panel in grooves provided by bottom door cap and side trim.

Slide the filler board into place behind the decorator panel, if necessary.

2.Attach the handle and trim.

3.Reinstall the refrigerator door.

Remove and Replace Freezer Drawer Panel

NOTE: You do not need to remove the freezer drawer to remove or replace the decorator panel.

1.Pull the freezer drawer out to access the handle screws.

2.Using a Phillips screwdriver, remove the handle screws and lift off the handle.

3.Slide the decorator panel and filler board up through handle opening.

4.Replace the decorator panels by reversing directions.

Care of Decorator Panels

1.Clean panels with stainless steel cleaner and polish or mild soap and water with a clean, soft, damp cloth.

2.Rinse panels thoroughly and blot dry using a dry, soft cloth or chamois.

NOTE: Do not use paper towels or cleaners which contain solvents such as ammonia. They can damage the surface of the panels.

Install Custom Wood Panels

If you plan to install custom wood decorator panels, you will need to create the panels yourself or consult your cabinetmaker or carpenter. See dimensional drawings for wood panel inserts.

Flat Panels:

You can create a custom flat panel a maximum of ¹⁄₄" (6.35 mm) thick to replace your decorator panels. Flat wood panels less than ¹⁄₄" (6.35 mm) thick are not recommended.

Raised Panels:

A raised panel design can be created by screwing or gluing wood panels to ¹⁄₄" (6.35 mm) backing or by using ³⁄₄" (19.05 mm) stock with routed edges. Allow 2¹⁄₂" (6.35 cm) minimum clearance between raised edge of panel and handle.

Weight requirements for raised panel inserts:

Refrigerator door panel should not exceed 30 lbs (14 kg).

Freezer drawer panels should not exceed 15 lbs (7 kg) combined weight.

13

Image 13
Contents BOTTOM-MOUNT Refrigerator Table DES Matières Table of ContentsBefore You Throw Away Your Old Refrigerator or Freezer Refrigerator SafetyClean Before Using Installation InstructionsUnpack the Refrigerator Location RequirementsWater Supply Requirements Electrical RequirementsConnect the Water Supply Style Connect to RefrigeratorRefrigerator Door Base GrilleRemove Door and Hinges Replace Handles Panel SeriesReverse Door Architect Series Reverse Door Panel SeriesReplace Door and Hinges Replace Drawer Freezer DrawerRemove Drawer Final StepsArchitect Series Door Swing Reversal optionalPanel Series Water System Preparation Adjust the DoorStyle 1 Front leveling Style 2 Front and rear levelingFactory Trim Kit on some models Dimensions for Routing Door Panel Side View Dimensions for Custom Wood PanelsNormal Sounds 20 cu. ft. Refrigerator doorAdjusting Electronic Controls Using the ControlsRefrigerator USE Ensuring Proper Air CirculationDigital Controls Water Filter Status Light Water DispenserWater Filtration System Refrigerator FeaturesRefrigerator Shelves Temperature-Controlled DrawerCrisper Humidity Control Crisper and Crisper CoverUtility or Egg Bin Freezer FeaturesFreezer Baskets Refrigerator Care Door FeaturesChanging the Light Bulb Power InterruptionsVacation and Moving Care Troubleshooting Off-taste, odor or gray color in the ice Ice maker is not producing ice or not enough iceWater dispenser will not operate properly Water flow from the dispenser decreases noticeablyDispenser water is not cool enough Temperature is too warmDivider between the two compartments is warm There is interior moisture buildupAccessories Assistance or ServiceWater Filter Certifications U.S.AApplication Guidelines/Water Supply Parameters Product Data SheetsONE Year Limited Warranty Kitchenaid Refrigerator WarrantyAvant de jeter votre vieux réfrigérateur ou congélateur Sécurité DU RéfrigérateurExigences demplacement Instructions D’INSTALLATIONDéballage du réfrigérateur Enlèvement des matériaux d’emballageSpécifications de l’alimentation en eau Spécifications électriquesRaccordement de la canalisation deau Raccordement au réfrigérateur Porte du réfrigérateur Grille de la baseEnlèvement de la porte et des charnières Remplacement des poignées série avec panneaux décoratifsInversion du sens douverture de la porte série Architect CaisseEnlèvement du tiroir Tiroir du congélateurÉtapes finales Série Architect Inversion du sens douverture des portes facultatifSérie avec panneaux décoratifs Préparation du système d’eau Ajustement de la porteStyle 1 Nivellement avant Style 2 Nivellement avant et arrièreEnsemble décoratif de l’usine Dimensions pour lusinage du panneau de porte vue latérale Dimensions pour les panneaux en bois personnalisésSons normaux Porte du réfrigérateur de 20 pi cuCommandes électroniques Utilisation des commandesAjustement des commandes électroniques Utilisation DU RéfrigérateurAjustement des commandes numériques Commandes numériquesDésactivation/activation du réfrigérateur Pour ajuster les réglages de températureDoor Alarm avertisseur de la porte Holiday Mode mode vacancesTemp Alarm alarme de dépassement de température Commandes numériques Préférences de lutilisateurSystème de filtration d’eau Distributeur d’eauTémoin lumineux de létat du filtre à eau Machine à glaçons Caractéristiques DU RéfrigérateurTablettes du réfrigérateur Tiroir à température contrôlée Bac à légumes et couvercleRéglage de l’humidité dans le bac à légumes Casier utilitaire ou oeufrier Caractéristiques DU CongélateurPaniers de congélateur Entretien DU Réfrigérateur Caractéristiques DE LA PorteRemplacement de lampoule du compartiment de réfrigération Remplacement de l’ampoule d’éclairageRemplacement de lampoule du compartiment de congélation Pannes de courantEntretien avant les vacances ou lors d’un déménagement DépannageDéménagement Les ampoules n’éclairent pasLe moteur semble fonctionner excessivement Le plat de dégivrage contient de l’eauLe réfrigérateur semble faire trop de bruit La machine à glaçons ne produit pas de glaçons ou pas assezLe débit d’eau du distributeur diminue beaucoup Le distributeur d’eau ne fonctionne pas bien’eau coule du distributeur ’eau du distributeur n’est pas assez froideAccessoires Assistance OU ServiceSystème de filtration d’eau intérieur Feuilles DE Données SUR LE ProduitGarantie Limitée DE UN AN Garantie DU Réfrigérateur KitchenaidAll rights reserved 12828153