KitchenAid 2266877 manual Custom Side Panels, Side by Side and Bottom Mount Side Panels

Page 12

Custom Side Panels

Side by Side and Bottom Mount Side Panels

Width and height of side panel is determined by installation type. Side panel should be a minimum of ¹⁄₂ in. (12 mm) thick to prevent warping. The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions. Install side panel (optional) support board on rear wall if opening depth is 25 in. (63.5 cm) or more.

241/8"

(61.3 cm)

2311/16"

(60.3 cm)

231/2"

(59.7 cm)

End View of Side Trim Dimensions:

Inset Side Panel

1.Measure the distance from point A (as shown) to back wall. Add ⁷⁄₃₂ in. (5.6 mm) to this measurement for side panel to fit into trim.

2.If panel is more than ¹⁄₄ in. (6 mm) thick, rout front edge of panel to fit trim piece.

A

1

1. Door

Flush Side Panel

1.Measure the distance from point A (as shown) to back wall.

2.Attach support board with screw or adhesive that is compatible with aluminum and wood.

1/4"

(6 mm)

1/16"

(1.5 mm)

7/32"

(5.5 mm)

5/32"

(4 mm)

A

1

2

3

1.Support board

2.Attachment locations

3.Door

Recessed Inset Side Panel

1.Measure the distance from point A (as shown) to back wall.

2.Rout front edge of support board or attach ¹⁄₄ in. (6 mm) board for retention in cabinet side trim.

1

13/32" (10 mm)

A

2

1.Support board

2.Door

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation Guide Guide D’INSTALLATIONManual DE Instalación Built-In RefrigeratorsSide bySide and Bottom MountTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantProduct Dimensions Tools and PartsSide View All models Top View All modelsOpening Dimensions Width of Refrigerator Model Width a as shown aboveLocation Requirements Location PreparationWidth of Opening Model Width a as shown above Electrical Requirements Water Supply RequirementsTipping Radius Door Swing Dimensions Side Tipping Radius see chart followingSide by Side Door Swing Dimensions Bottom Mount Models Door Swing DimensionsFactory Panels and Kits Custom Top Grille and Door Panels Door Panels for Non-dispenser ModelsDoor Panels for Dispenser Models Refrigerator and Freezer Door Panels Routing for Custom Top Grille and Door Panels all modelsTop Grille Panel Routing Door Panel RoutingEnd View of Side Trim Dimensions Inset Side Panel Custom Side PanelsSide by Side and Bottom Mount Side Panels Flush Side PanelInstallation Instructions Unpack RefrigeratorReduce Tipping Radius Model Reduced Tipping RadiusInstall Anti-Tip Boards Install New Water LineTo install anti-tip boards Wraparound modelsStyle 1 Connecting to a Water Line Style 2 Connecting to a Water ValveWater System Connection Plug in RefrigeratorInstall Door Panels Move Refrigerator to Final PositionLower Leveling Legs Level RefrigeratorAdjust Doors Door Height AdjustmentDoor Alignment Install Decorative Top Panel Door Swing AdjustmentAdding a Decorative Panel to the Top Grille Assembly Install Side Panel Install Base GrilleComplete Installation Seguridad DEL Refrigerador Su seguridad y la seguridad de los demá s es muy importanteMedidas del producto Piezas y herramientasVista lateral Todos los modelos Herramientas requeridasVista superior Todos los modelos Vista frontal para los modelos de dos puertasVista delantera para los modelos de montaje inferior Medidas de aberturaRequisitos de ubicación Cm mínRequisitos eléctricos Requisitos de suministro de aguaMétodo de conexión a tierra recomendado Suministro de agua fríaArco de vuelco Medidas de oscilación de las puertasMedidas de oscilación de dos puertas Arco de vuelco hacia adelante igual para todos los modelosPaneles y juegos de fábrica Medidas de oscilación de las puertas de montaje inferiorJuegos de paneles y agarraderas de dos puertas Juegos de paneles para puertas de fábricaPaneles a la medida para la rejilla Superior y las puertas Juego para rejilla superiorJuego para rejilla superior de modelos con panel Juego de rejilla superior para modelos envolventesPaneles de puerta para modelos sin despachador Paneles de puerta para modelos con despachadorPaneles de puertas de refrigerador y congelador Contorneado del panel de la rejilla superiorPaneles laterales a la medida Contorneado del panel de la puertaPaneles laterales de dos puertas y de montaje inferior Medidas del adorno lateral visto desde atrásInstrucciones DE Instalación Cómo desempacar su refrigeradorPanel lateral en relieve Panel lateral al rasCómo reducir el arco de vuelco Cómo instalar los tableros anti-vuelcoModelo Arco de vuelco reducido Modelos con panelesInstalación de una tubería de agua Nueva Cómo conectar el sistema de aguaCómo instalar los tableros antivuelco Cómo enchufar el refrigerador Ubicación final del refrigeradorEstilo 2 Conexión a una válvula de agua Patas niveladoras inferiores Cómo instalar los paneles de la puertaCómo nivelar el refrigerador Modelos con panelCómo ajustar las puertas Cómo alinear las puertasCómo ajustar la altura de la puerta Cómo instalar el panel decorativo Superior Cómo ajustar la oscilación de las puertasCómo instalar el panel lateral Cómo instalar la rejilla de la baseCómo terminar la instalación Sécurité DU Réfrigérateur Votre sé curité et celle des autres est trè s importanteExigences ’INSTALLATION Dimensions du produitOutillage et pièces nécessaires Vue latérale Tous les modèlesDimensions de l’ouverture Préparation de lemplacementVue de dessus Tous les modèles Vue avant pour les modèles côte à côteExigences d’emplacement Risque dexplosionSpécifications électriques Spécifications de l’alimentation en eauRayon de basculement Dimensions pour le pivotement Des portes Rayon de basculement latéral voir le tableau suivantModèles de 42 po 106 cm Modèles de 48 po 122 cmEnsembles de panneaux dorigine Ensembles de panneaux de porte dorigineEnsembles de poignées de porte prolongées Ensemble de la grille supérieurePanneaux personnalisés de la grille Supérieure et de porte Panneaux de porte pour modèles sans distributeurPanneaux de porte pour modèles avec distributeur Couleur Ouverture vers Ouverture vers la La gauche DroitePanneaux de porte de réfrigérateur et de congélateur Usinage du panneau de la grille supérieureUsinage du panneau de porte Dimensions pour lusinage du panneau de porte vue latérale Panneaux latéraux personnalisésPanneau latéral inséré Panneau latéral en affleurementInstructions ’INSTALLATION Déballage du réfrigérateurRéduction du rayon de basculement Panneau latéral inséré en retraitInstallation de planches Anti-basculement Installation des planches antibasculementModèles à panneaux Modèles à portes enveloppantesInstallation d’une nouvelle Canalisation d’eau Raccordement de la canalisation d’eauStyle 2 Raccordement au robinet deau Déplacement du réfrigérateur à Lemplacement final Installation des panneaux de porteBrancher le réfrigérateur Déploiement des pieds de nivellementNivellement du réfrigérateur Ajustement des portesAlignement des portes Réfrigérateurs côte à côteAjustement de la hauteur des portes Ajustement de l’ouverture des portesRéfrigérateurs superposés Installation du panneau décoratif Supérieur Installation du panneau latéralAddition dun panneau décoratif à la grille supérieure Installation de la grille de la base Achever l’installation2266877 All rights reserved

2266877 specifications

The KitchenAid 2266877 is an essential kitchen appliance that epitomizes convenience, durability, and style. As part of KitchenAid’s renowned lineup, this model is designed to cater to both amateur cooks and seasoned chefs. One of its standout features is the robust motor that ensures efficient mixing and kneading, while maintaining a quiet operation. This powerful motor is complemented by a range of speed settings, allowing users to choose the perfect speed for various tasks, from whipping egg whites to kneading pizza dough.

The construction of the KitchenAid 2266877 is marked by its high-quality materials. The body is crafted from sturdy metal, ensuring longevity and stability during use. Additionally, the mixer’s sleek design makes it an attractive addition to any kitchen countertop. Available in multiple colors, it can easily match different aesthetic preferences, making it as much a decorative piece as a functional appliance.

In terms of technologies, the KitchenAid 2266877 boasts an innovative planetary mixing action. This means that the mixing attachment moves in one direction while the bowl rotates in the opposite direction, ensuring that all ingredients are mixed thoroughly without any manual intervention. This feature is particularly useful for baking, as it promotes an even consistency and reduces the risk of lumps in the mixture.

The appliance comes equipped with different attachments that enhance its versatility. The standard wire whip, flat beater, and dough hook allow users to tackle a wide range of recipes, from delicate meringues to robust bread doughs. Its compatibility with additional attachments like pasta makers and food grinders further expands its functional utility, making it a valuable investment for anyone who enjoys cooking or baking.

Another remarkable characteristic of the KitchenAid 2266877 is its easy-to-use control panel. The intuitive design enables users to adjust speeds and settings effortlessly. Additionally, it features a tilt-head design, allowing for easy access to the bowl and attachments for quick installation and cleaning.

In conclusion, the KitchenAid 2266877 stands out for its powerful performance, durable construction, and versatile capabilities. This mixer is ideal for anyone looking to elevate their culinary skills while enjoying the convenience of a high-quality kitchen appliance. Its combination of technology, functionality, and style makes it a must-have for any kitchen enthusiast.
Top Page Image Contents