KitchenAid 2266877 Install Anti-Tip Boards, Install New Water Line, To install anti-tip boards

Page 14

4.Stand the refrigerator by first placing the left bottom edge of the refrigerator on floor, standing the product upright and then lowering the right side of the refrigerator down to the floor.

5.Reassemble the trim and top grille after dolly has been removed from refrigerator.

Wraparound models

1.Grasp both ends of louver panel. Push louver panel straight up, then pull straight out. Lay the panel on a soft surface.

2.Grasp both ends of the top grille. Push top grille straight up, then pull straight out. Lay the top grille on a soft surface.

1.Top grille

2.Cabinet side trim

3.Louver panel

3.Remove the 6 screws attaching each cabinet side trim to the refrigerator and remove the side trims.

4.Stand the refrigerator up by first placing the left bottom edge of the refrigerator on floor, standing the product upright and then lowering the right side of the refrigerator down to the floor.

5.Reassemble the trim and top grille after dolly has been removed from refrigerator.

Install Anti-Tip Boards

IMPORTANT:

■The solid soffit must be within 1 in. (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1 in. (2.5 cm) or one is not available, prevent the refrigerator from tipping during use as shown.

■It is recommended that board(s) be installed before refrigerator is installed.

■Board(s) must be long enough to fully cover width of compressor cover.

■Locate the board(s) so the bottom surface of the board(s) are 84 in. (213 cm) from the floor.

■During installation, raise the refrigerator up so there is

¹⁄₄ in. (6.4 mm) maximum between top of the refrigerator and bottom of anti-tip board(s). Do not crush the condenser cover when raising the rear leveling legs.

To install anti-tip boards

1. Mark stud locations on rear wall 80 in. to 90 in. (203 - 229 cm) above floor.

2. Securely attach one or two 2 in. x 4 in. x 32 in.

(5 cm x 10 cm x 81 cm) wood boards to wall studs behind refrigerator. Use 6 - #8 x 3 in. (7.6 mm) (or longer) wood screws.The wood screws must be screwed into the studs at least 1½ in. (3.8 cm). The board(s) must overlap the compressor cover.

1 2

3

2" (5 cm)

4

1.Center board ¹⁄₄ in. (6 mm) max. above refrigerator

2.Two, 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards

3.Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws

4.Compressor cover

Install New Water Line

(if required)

Tools required: Flat-blade screwdriver, ⁷⁄₁₆ in. and ¹⁄₂ in. open- end wrenches or two adjustable wrenches, ¹⁄₄ in. nut driver and drill bit, hand drill or electric drill (properly grounded).

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Find a ½ in. to 1¹⁄₄ in. (12.7 mm to 3.18 cm) vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Manual DE Instalación Installation GuideGuide D’INSTALLATION Built-In RefrigeratorsSide bySide and Bottom MountTable DES Matières Table of ContentsÍndice Refrigerator Safety Your safety and the safety of others are very importantSide View All models Product DimensionsTools and Parts Top View All modelsOpening Dimensions Width of Refrigerator Model Width a as shown aboveWidth of Opening Model Width a as shown above Location RequirementsLocation Preparation Tipping Radius Electrical RequirementsWater Supply Requirements Side by Side Door Swing Dimensions Door Swing DimensionsSide Tipping Radius see chart following Bottom Mount Models Door Swing DimensionsFactory Panels and Kits Door Panels for Dispenser Models Custom Top Grille and Door PanelsDoor Panels for Non-dispenser Models Top Grille Panel Routing Refrigerator and Freezer Door PanelsRouting for Custom Top Grille and Door Panels all models Door Panel RoutingSide by Side and Bottom Mount Side Panels End View of Side Trim Dimensions Inset Side PanelCustom Side Panels Flush Side PanelReduce Tipping Radius Installation InstructionsUnpack Refrigerator Model Reduced Tipping RadiusTo install anti-tip boards Install Anti-Tip BoardsInstall New Water Line Wraparound modelsWater System Connection Style 1 Connecting to a Water LineStyle 2 Connecting to a Water Valve Plug in RefrigeratorLower Leveling Legs Install Door PanelsMove Refrigerator to Final Position Level RefrigeratorDoor Alignment Adjust DoorsDoor Height Adjustment Adding a Decorative Panel to the Top Grille Assembly Install Decorative Top PanelDoor Swing Adjustment Complete Installation Install Side PanelInstall Base Grille Seguridad DEL Refrigerador Su seguridad y la seguridad de los demá s es muy importanteVista lateral Todos los modelos Medidas del productoPiezas y herramientas Herramientas requeridasVista delantera para los modelos de montaje inferior Vista superior Todos los modelosVista frontal para los modelos de dos puertas Medidas de aberturaRequisitos de ubicación Cm mínMétodo de conexión a tierra recomendado Requisitos eléctricosRequisitos de suministro de agua Suministro de agua fríaMedidas de oscilación de dos puertas Arco de vuelcoMedidas de oscilación de las puertas Arco de vuelco hacia adelante igual para todos los modelosJuegos de paneles y agarraderas de dos puertas Paneles y juegos de fábricaMedidas de oscilación de las puertas de montaje inferior Juegos de paneles para puertas de fábricaJuego para rejilla superior de modelos con panel Paneles a la medida para la rejilla Superior y las puertasJuego para rejilla superior Juego de rejilla superior para modelos envolventesPaneles de puertas de refrigerador y congelador Paneles de puerta para modelos sin despachadorPaneles de puerta para modelos con despachador Contorneado del panel de la rejilla superiorPaneles laterales de dos puertas y de montaje inferior Paneles laterales a la medidaContorneado del panel de la puerta Medidas del adorno lateral visto desde atrásPanel lateral en relieve Instrucciones DE InstalaciónCómo desempacar su refrigerador Panel lateral al rasModelo Arco de vuelco reducido Cómo reducir el arco de vuelcoCómo instalar los tableros anti-vuelco Modelos con panelesCómo instalar los tableros antivuelco Instalación de una tubería de agua NuevaCómo conectar el sistema de agua Estilo 2 Conexión a una válvula de agua Cómo enchufar el refrigeradorUbicación final del refrigerador Cómo nivelar el refrigerador Patas niveladoras inferioresCómo instalar los paneles de la puerta Modelos con panelCómo ajustar la altura de la puerta Cómo ajustar las puertasCómo alinear las puertas Cómo instalar el panel decorativo Superior Cómo ajustar la oscilación de las puertasCómo terminar la instalación Cómo instalar el panel lateralCómo instalar la rejilla de la base Sécurité DU Réfrigérateur Votre sé curité et celle des autres est trè s importanteOutillage et pièces nécessaires Exigences ’INSTALLATIONDimensions du produit Vue latérale Tous les modèlesVue de dessus Tous les modèles Dimensions de l’ouverturePréparation de lemplacement Vue avant pour les modèles côte à côteExigences d’emplacement Risque dexplosionRayon de basculement Spécifications électriquesSpécifications de l’alimentation en eau Modèles de 42 po 106 cm Dimensions pour le pivotement Des portesRayon de basculement latéral voir le tableau suivant Modèles de 48 po 122 cmEnsembles de poignées de porte prolongées Ensembles de panneaux dorigineEnsembles de panneaux de porte dorigine Ensemble de la grille supérieurePanneaux de porte pour modèles avec distributeur Panneaux personnalisés de la grille Supérieure et de portePanneaux de porte pour modèles sans distributeur Couleur Ouverture vers Ouverture vers la La gauche DroiteUsinage du panneau de porte Panneaux de porte de réfrigérateur et de congélateurUsinage du panneau de la grille supérieure Panneau latéral inséré Dimensions pour lusinage du panneau de porte vue latéralePanneaux latéraux personnalisés Panneau latéral en affleurementRéduction du rayon de basculement Instructions ’INSTALLATIONDéballage du réfrigérateur Panneau latéral inséré en retraitModèles à panneaux Installation de planches Anti-basculementInstallation des planches antibasculement Modèles à portes enveloppantesStyle 2 Raccordement au robinet deau Installation d’une nouvelle Canalisation d’eauRaccordement de la canalisation d’eau Brancher le réfrigérateur Déplacement du réfrigérateur à Lemplacement finalInstallation des panneaux de porte Déploiement des pieds de nivellementAlignement des portes Nivellement du réfrigérateurAjustement des portes Réfrigérateurs côte à côteRéfrigérateurs superposés Ajustement de la hauteur des portesAjustement de l’ouverture des portes Addition dun panneau décoratif à la grille supérieure Installation du panneau décoratif SupérieurInstallation du panneau latéral Installation de la grille de la base Achever l’installation2266877 All rights reserved

2266877 specifications

The KitchenAid 2266877 is an essential kitchen appliance that epitomizes convenience, durability, and style. As part of KitchenAid’s renowned lineup, this model is designed to cater to both amateur cooks and seasoned chefs. One of its standout features is the robust motor that ensures efficient mixing and kneading, while maintaining a quiet operation. This powerful motor is complemented by a range of speed settings, allowing users to choose the perfect speed for various tasks, from whipping egg whites to kneading pizza dough.

The construction of the KitchenAid 2266877 is marked by its high-quality materials. The body is crafted from sturdy metal, ensuring longevity and stability during use. Additionally, the mixer’s sleek design makes it an attractive addition to any kitchen countertop. Available in multiple colors, it can easily match different aesthetic preferences, making it as much a decorative piece as a functional appliance.

In terms of technologies, the KitchenAid 2266877 boasts an innovative planetary mixing action. This means that the mixing attachment moves in one direction while the bowl rotates in the opposite direction, ensuring that all ingredients are mixed thoroughly without any manual intervention. This feature is particularly useful for baking, as it promotes an even consistency and reduces the risk of lumps in the mixture.

The appliance comes equipped with different attachments that enhance its versatility. The standard wire whip, flat beater, and dough hook allow users to tackle a wide range of recipes, from delicate meringues to robust bread doughs. Its compatibility with additional attachments like pasta makers and food grinders further expands its functional utility, making it a valuable investment for anyone who enjoys cooking or baking.

Another remarkable characteristic of the KitchenAid 2266877 is its easy-to-use control panel. The intuitive design enables users to adjust speeds and settings effortlessly. Additionally, it features a tilt-head design, allowing for easy access to the bowl and attachments for quick installation and cleaning.

In conclusion, the KitchenAid 2266877 stands out for its powerful performance, durable construction, and versatile capabilities. This mixer is ideal for anyone looking to elevate their culinary skills while enjoying the convenience of a high-quality kitchen appliance. Its combination of technology, functionality, and style makes it a must-have for any kitchen enthusiast.
Top Page Image Contents