KitchenAid 2266877 manual Adjust Doors, Door Alignment, Door Height Adjustment

Page 17

2.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from left to right.

1

1

2

2

1.Rear leveling bolt

2.Front level bolt

3.Place the level(s) on shelf or shelves as shown. Check to see whether the refrigerator is level from front to back.

4.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from front to back.

5.Be sure that all four leveling legs contact the floor and support the full weight of the refrigerator.

6.Make final check to ensure the refrigerator is level.

Adjust Doors

Door Alignment

Use the following steps to adjust door alignment if doors need to be adjusted left, right, in or out.

1.Inspect spacing of the gap between the freezer door and the refrigerator door. Make sure the spacing between the doors is the same distance at the top and the bottom.

1

1.Uneven door gap

2.If the door gap is uneven, the side trim must be removed to see the entire door gasket liner. Remove the six Phillips screws holding side trim.

3.Loosen the four T27 flat-head mounting screws on top of both hinges. Loosen the two ¹⁄₄ in. hex-head mounting screws. Loosen screws to the point that the hinge is movable, but there is friction when trying to move the hinge.

1.T27 6-point drive flat-head mounting screws

2.¹⁄₄ in. hex-head mounting screws

4.Adjust the hinges so that the door gap is the same distance at the top as it is at the bottom. The bottom distance should be used as the template for the top.

5.Check the side door gasket gap. Make sure that the distance is the same at the top and the bottom. Adjust the hinges, if necessary.

6.Recheck the front door gap spacing to ensure it is still aligned and even.

7.Tighten down the mounting screws on both hinges.

8.Reinstall the side door trims.

Door Height Adjustment

Use the following steps to adjust the door height, up or down, after the doors have been leveled.

1.Open the freezer or refrigerator door and locate the hinge assembly at the bottom of the door needing to be adjusted.

1.Locking plate

2.Door stop screw

3.Bushing

2.Remove the door stop screw from the bottom door hinge using the Allen wrench. Remove locking plate as shown.

3.Turn the bushing located underneath the bottom of the hinge using the open-end wrench. Turning the bushing to the left (counterclockwise) will raise the door. Turning the bushing right (clockwise) will lower the door.

4.After adjusting, check the doors to make sure they are even at the top and bottom. If the doors are not even, continue to turn the bushing to adjust the door height.

5.Replace the locking plate.

6.Turn the bushing slightly to align the hinge and locking plate screw holes.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Guide D’INSTALLATION Installation GuideManual DE Instalación Built-In RefrigeratorsSide bySide and Bottom MountTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyTools and Parts Product DimensionsSide View All models Top View All modelsWidth of Refrigerator Model Width a as shown above Opening DimensionsWidth of Opening Model Width a as shown above Location RequirementsLocation Preparation Tipping Radius Electrical RequirementsWater Supply Requirements Side Tipping Radius see chart following Door Swing DimensionsSide by Side Door Swing Dimensions Bottom Mount Models Door Swing DimensionsFactory Panels and Kits Door Panels for Dispenser Models Custom Top Grille and Door PanelsDoor Panels for Non-dispenser Models Routing for Custom Top Grille and Door Panels all models Refrigerator and Freezer Door PanelsTop Grille Panel Routing Door Panel RoutingCustom Side Panels End View of Side Trim Dimensions Inset Side PanelSide by Side and Bottom Mount Side Panels Flush Side PanelUnpack Refrigerator Installation InstructionsReduce Tipping Radius Model Reduced Tipping RadiusInstall New Water Line Install Anti-Tip BoardsTo install anti-tip boards Wraparound modelsStyle 2 Connecting to a Water Valve Style 1 Connecting to a Water LineWater System Connection Plug in RefrigeratorMove Refrigerator to Final Position Install Door PanelsLower Leveling Legs Level RefrigeratorDoor Alignment Adjust DoorsDoor Height Adjustment Adding a Decorative Panel to the Top Grille Assembly Install Decorative Top PanelDoor Swing Adjustment Complete Installation Install Side PanelInstall Base Grille Su seguridad y la seguridad de los demá s es muy importante Seguridad DEL RefrigeradorPiezas y herramientas Medidas del productoVista lateral Todos los modelos Herramientas requeridasVista frontal para los modelos de dos puertas Vista superior Todos los modelosVista delantera para los modelos de montaje inferior Medidas de aberturaCm mín Requisitos de ubicaciónRequisitos de suministro de agua Requisitos eléctricosMétodo de conexión a tierra recomendado Suministro de agua fríaMedidas de oscilación de las puertas Arco de vuelcoMedidas de oscilación de dos puertas Arco de vuelco hacia adelante igual para todos los modelosMedidas de oscilación de las puertas de montaje inferior Paneles y juegos de fábricaJuegos de paneles y agarraderas de dos puertas Juegos de paneles para puertas de fábricaJuego para rejilla superior Paneles a la medida para la rejilla Superior y las puertasJuego para rejilla superior de modelos con panel Juego de rejilla superior para modelos envolventesPaneles de puerta para modelos con despachador Paneles de puerta para modelos sin despachadorPaneles de puertas de refrigerador y congelador Contorneado del panel de la rejilla superiorContorneado del panel de la puerta Paneles laterales a la medidaPaneles laterales de dos puertas y de montaje inferior Medidas del adorno lateral visto desde atrásCómo desempacar su refrigerador Instrucciones DE InstalaciónPanel lateral en relieve Panel lateral al rasCómo instalar los tableros anti-vuelco Cómo reducir el arco de vuelcoModelo Arco de vuelco reducido Modelos con panelesCómo instalar los tableros antivuelco Instalación de una tubería de agua NuevaCómo conectar el sistema de agua Estilo 2 Conexión a una válvula de agua Cómo enchufar el refrigeradorUbicación final del refrigerador Cómo instalar los paneles de la puerta Patas niveladoras inferioresCómo nivelar el refrigerador Modelos con panelCómo ajustar la altura de la puerta Cómo ajustar las puertasCómo alinear las puertas Cómo ajustar la oscilación de las puertas Cómo instalar el panel decorativo SuperiorCómo terminar la instalación Cómo instalar el panel lateralCómo instalar la rejilla de la base Votre sé curité et celle des autres est trè s importante Sécurité DU RéfrigérateurDimensions du produit Exigences ’INSTALLATIONOutillage et pièces nécessaires Vue latérale Tous les modèlesPréparation de lemplacement Dimensions de l’ouvertureVue de dessus Tous les modèles Vue avant pour les modèles côte à côteRisque dexplosion Exigences d’emplacementRayon de basculement Spécifications électriquesSpécifications de l’alimentation en eau Rayon de basculement latéral voir le tableau suivant Dimensions pour le pivotement Des portesModèles de 42 po 106 cm Modèles de 48 po 122 cmEnsembles de panneaux de porte dorigine Ensembles de panneaux dorigineEnsembles de poignées de porte prolongées Ensemble de la grille supérieurePanneaux de porte pour modèles sans distributeur Panneaux personnalisés de la grille Supérieure et de portePanneaux de porte pour modèles avec distributeur Couleur Ouverture vers Ouverture vers la La gauche DroiteUsinage du panneau de porte Panneaux de porte de réfrigérateur et de congélateurUsinage du panneau de la grille supérieure Panneaux latéraux personnalisés Dimensions pour lusinage du panneau de porte vue latéralePanneau latéral inséré Panneau latéral en affleurementDéballage du réfrigérateur Instructions ’INSTALLATIONRéduction du rayon de basculement Panneau latéral inséré en retraitInstallation des planches antibasculement Installation de planches Anti-basculementModèles à panneaux Modèles à portes enveloppantesStyle 2 Raccordement au robinet deau Installation d’une nouvelle Canalisation d’eauRaccordement de la canalisation d’eau Installation des panneaux de porte Déplacement du réfrigérateur à Lemplacement finalBrancher le réfrigérateur Déploiement des pieds de nivellementAjustement des portes Nivellement du réfrigérateurAlignement des portes Réfrigérateurs côte à côteRéfrigérateurs superposés Ajustement de la hauteur des portesAjustement de l’ouverture des portes Addition dun panneau décoratif à la grille supérieure Installation du panneau décoratif SupérieurInstallation du panneau latéral Achever l’installation Installation de la grille de la baseAll rights reserved 2266877

2266877 specifications

The KitchenAid 2266877 is an essential kitchen appliance that epitomizes convenience, durability, and style. As part of KitchenAid’s renowned lineup, this model is designed to cater to both amateur cooks and seasoned chefs. One of its standout features is the robust motor that ensures efficient mixing and kneading, while maintaining a quiet operation. This powerful motor is complemented by a range of speed settings, allowing users to choose the perfect speed for various tasks, from whipping egg whites to kneading pizza dough.

The construction of the KitchenAid 2266877 is marked by its high-quality materials. The body is crafted from sturdy metal, ensuring longevity and stability during use. Additionally, the mixer’s sleek design makes it an attractive addition to any kitchen countertop. Available in multiple colors, it can easily match different aesthetic preferences, making it as much a decorative piece as a functional appliance.

In terms of technologies, the KitchenAid 2266877 boasts an innovative planetary mixing action. This means that the mixing attachment moves in one direction while the bowl rotates in the opposite direction, ensuring that all ingredients are mixed thoroughly without any manual intervention. This feature is particularly useful for baking, as it promotes an even consistency and reduces the risk of lumps in the mixture.

The appliance comes equipped with different attachments that enhance its versatility. The standard wire whip, flat beater, and dough hook allow users to tackle a wide range of recipes, from delicate meringues to robust bread doughs. Its compatibility with additional attachments like pasta makers and food grinders further expands its functional utility, making it a valuable investment for anyone who enjoys cooking or baking.

Another remarkable characteristic of the KitchenAid 2266877 is its easy-to-use control panel. The intuitive design enables users to adjust speeds and settings effortlessly. Additionally, it features a tilt-head design, allowing for easy access to the bowl and attachments for quick installation and cleaning.

In conclusion, the KitchenAid 2266877 stands out for its powerful performance, durable construction, and versatile capabilities. This mixer is ideal for anyone looking to elevate their culinary skills while enjoying the convenience of a high-quality kitchen appliance. Its combination of technology, functionality, and style makes it a must-have for any kitchen enthusiast.
Top Page Image Contents