KitchenAid KAD-9 manual Component Locations, In-Tub Components, Tub-Mounted Components

Page 43

COMPONENT ACCESS

This section instructs you on how to service each component inside the Drawer Dishwasher. The components and their locations are shown below.

COMPONENT LOCATIONS

In-Tub Components

Spray Arm

Impeller

Coarse Filter

Hall Sensor

Heater Element

Drying Fan

Controller

Wash & Drain Motor

Rinse Aid LED

Rinse Aid & Detergent

Dispenser Pumps

Tub-Mounted Components

Water Fill

Valve

	Lid Motor	Power Cord
	(1 of 4)	Power Cord
	(1 of 4)

Chassis

Module

Cabinet-Mounted Components

4-1

Image 43

Contents Drawer Dishwasher Goals and Objectives ForwardTable of Contents Diagnostics & Troubleshooting General Safety FirstD D 01 D P PA Model & Serial Number DesignationsModel Number Serial NumberModel & Serial Number Label Tech Sheet Locations General SpecificationsTWO-YEAR Full Warranty Kitchenaid Dishwasher WarrantyKitchenAid will not pay for Page Tools and Material Required GeneralParts Supplied 32-3/16 34-1/2 Cm 87.8 cm Product DimensionsFrom front Cabinet Dimensions / RequirementsForagrounded,cord-connecteddishwasher Electrical RequirementsWater Requirements Recommended Ground MethodPower Supply Cord Installing the DishwasherSide Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installationsStandard Front Panels Front Panels & TOE KickStandard Toe Kick Toe kick Custom Front Panels Custom Front Panels DimensionsLay the custom front panel face down Custom Toe Kick Custom Toe Kick DimensionsSystem Overview LID System Drain CycleFilter Plate Drying CycleControl Panels Parts and FeaturesDishwasher Systems To Clean The Spray ArmWash System Drying System To Clean The Drain FilterTo Clean The Filter Plate Sound SystemDetergent USE Using the DishwasherFilling The Powdered Detergent Dispenser Program Quantities How Much Detergent To UseHow Much Rinse Aid To Use Rinse Aid IndicatorRinse AID Dispenser Filling The DispenserPerformance Tips Wash Programs Program ChartsOption Selections Adjustments Canceling a Wash CyclePausing a Cycle Changing a Cycle Or SettingControl Lock Delay Start ModeTo enter the Option Adjustment Mode To adjust the Rinse Aid settingTo disable the End of Wash Program beeps To disable the Auto PowerPage Cabinet-Mounted Components Component LocationsIn-Tub Components Tub-Mounted ComponentsRemoving the Spray ARM and Impeller To remove the isolator Removing the ISOLATOR, BADGE, & Door HandleOn the next Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors To remove the power cord Removing the Chassis Module and Power CordTo remove the chassis module Removing the Water Fill Valves Drying FAN Component TestingWash & Drain Motor Rinse AID and Detergent DispenserLID Motor Power Resistor & HeaterTo test the heater, touch the ohmmeter Water Fill Valves Temperature SensorError Code Display Mode DiagnosticsError Codes Failed Heater Element Temperature Sensor FailedBad Wiring Or Connections Moisture / Foreign Matter On Chassis Board Flood Switch PCBInlet Valve Failed Moisture Around Temperature SensorWiring Or Connections Bad Water Supply Valve Turned OffFast Test Cycle Diagnostic ModesHardware Output Test Tub Home Sensor TestResistance Checks Troubleshooting ChartWiring Diagram Page United States Product Specifications Warranty Information Sources