KitchenAid KAD-9 manual Diagnostics, Error Code Display Mode

Page 63

DIAGNOSTICS & TROUBLESHOOTING

DIAGNOSTICS

THE ERROR CODE DISPLAY MODE

To enter the error code display mode:

1.Press the Power button for the Power On mode.

2.Press the Keylock button, and then the Start/Pause button. Hold both buttons for 5 seconds. The Start/Pause LED is on.

3.Press Start/Pause. The current error code is displayed on the drawer control panel LEDs, followed by the previous error code.

4.Press the Keylock button to clear the cur- rent error code. Press Keylock again to clear the previous error code.

5.Press the Power button to exit the Error Code Display mode.

6-1

Image 63

Contents Drawer Dishwasher Goals and Objectives ForwardTable of Contents Diagnostics & Troubleshooting General Safety FirstD D 01 D P PA Model & Serial Number DesignationsModel Number Serial NumberModel & Serial Number Label Tech Sheet Locations General SpecificationsKitchenaid Dishwasher Warranty TWO-YEAR Full WarrantyKitchenAid will not pay for Page General Tools and Material RequiredParts Supplied 32-3/16 34-1/2 Cm 87.8 cm Product DimensionsFrom front Cabinet Dimensions / RequirementsForagrounded,cord-connecteddishwasher Electrical RequirementsWater Requirements Recommended Ground MethodPower Supply Cord Installing the DishwasherSide Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installationsFront Panels & TOE Kick Standard Front PanelsStandard Toe Kick Toe kick Custom Front Panels Custom Front Panels DimensionsLay the custom front panel face down Custom Toe Kick Custom Toe Kick DimensionsSystem Overview LID System Drain CycleFilter Plate Drying CycleControl Panels Parts and FeaturesTo Clean The Spray Arm Dishwasher SystemsWash System Drying System To Clean The Drain FilterTo Clean The Filter Plate Sound SystemUsing the Dishwasher Detergent USEFilling The Powdered Detergent Dispenser Program Quantities How Much Detergent To UseHow Much Rinse Aid To Use Rinse Aid IndicatorRinse AID Dispenser Filling The DispenserPerformance Tips Wash Programs Program ChartsOption Selections Adjustments Canceling a Wash CyclePausing a Cycle Changing a Cycle Or SettingControl Lock Delay Start ModeTo enter the Option Adjustment Mode To adjust the Rinse Aid settingTo disable the End of Wash Program beeps To disable the Auto PowerPage Cabinet-Mounted Components Component LocationsIn-Tub Components Tub-Mounted ComponentsRemoving the Spray ARM and Impeller Removing the ISOLATOR, BADGE, & Door Handle To remove the isolatorOn the next Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors Removing the Chassis Module and Power Cord To remove the power cordTo remove the chassis module Removing the Water Fill Valves Drying FAN Component TestingWash & Drain Motor Rinse AID and Detergent DispenserPower Resistor & Heater LID MotorTo test the heater, touch the ohmmeter Water Fill Valves Temperature SensorError Code Display Mode DiagnosticsError Codes Failed Heater Element Temperature Sensor FailedBad Wiring Or Connections Moisture / Foreign Matter On Chassis Board Flood Switch PCBInlet Valve Failed Moisture Around Temperature SensorWiring Or Connections Bad Water Supply Valve Turned OffFast Test Cycle Diagnostic ModesHardware Output Test Tub Home Sensor TestResistance Checks Troubleshooting ChartWiring Diagram Page United States Product Specifications Warranty Information Sources