KitchenAid KAD-9 manual Removing the Controller

Page 49

REMOVING THE CONTROLLER

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug dishwasher or disconnect power.

2.Turn off the water going to the dishwasher.

3.Disconnect the drain line from the dish- washer.

4.Remove the door panel from the drawer (see page 4-4 for the procedure).

Controller

5.Pull the five connectors from the edges of the controller board.

6.Press in on the locking tab of the controller and remove the controller from the drawer.

6-Wire BADGE

4-Wire DISPENSER

4-Wire FAN

CONTROLLER

Locking Tab

6-Wire MOTOR

14-Wire CHASSIS

4-7

Image 49
Contents Drawer Dishwasher Goals and Objectives ForwardTable of Contents Diagnostics & Troubleshooting General Safety FirstModel Number Model & Serial Number DesignationsSerial Number D D 01 D P PAModel & Serial Number Label Tech Sheet Locations General SpecificationsTWO-YEAR Full Warranty Kitchenaid Dishwasher WarrantyKitchenAid will not pay for Page Tools and Material Required GeneralParts Supplied 32-3/16 34-1/2 Cm 87.8 cm Product DimensionsFrom front Cabinet Dimensions / RequirementsWater Requirements Electrical RequirementsRecommended Ground Method Foragrounded,cord-connecteddishwasherPower Supply Cord Installing the DishwasherSide Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installationsStandard Front Panels Front Panels & TOE KickStandard Toe Kick Toe kick Custom Front Panels Custom Front Panels DimensionsLay the custom front panel face down Custom Toe Kick Custom Toe Kick DimensionsSystem Overview Filter Plate Drain CycleDrying Cycle LID SystemControl Panels Parts and FeaturesDishwasher Systems To Clean The Spray ArmWash System To Clean The Filter Plate To Clean The Drain FilterSound System Drying SystemDetergent USE Using the DishwasherFilling The Powdered Detergent Dispenser Program Quantities How Much Detergent To UseRinse AID Dispenser Rinse Aid IndicatorFilling The Dispenser How Much Rinse Aid To UsePerformance Tips Wash Programs Program ChartsPausing a Cycle Canceling a Wash CycleChanging a Cycle Or Setting Option Selections AdjustmentsTo enter the Option Adjustment Mode Delay Start ModeTo adjust the Rinse Aid setting Control LockTo disable the End of Wash Program beeps To disable the Auto PowerPage In-Tub Components Component LocationsTub-Mounted Components Cabinet-Mounted ComponentsRemoving the Spray ARM and Impeller To remove the isolator Removing the ISOLATOR, BADGE, & Door HandleOn the next Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors To remove the power cord Removing the Chassis Module and Power CordTo remove the chassis module Removing the Water Fill Valves Drying FAN Component TestingWash & Drain Motor Rinse AID and Detergent DispenserLID Motor Power Resistor & HeaterTo test the heater, touch the ohmmeter Water Fill Valves Temperature SensorError Code Display Mode DiagnosticsError Codes Bad Wiring Or Connections Temperature Sensor FailedMoisture / Foreign Matter On Chassis Board Flood Switch PCB Failed Heater ElementWiring Or Connections Bad Moisture Around Temperature SensorWater Supply Valve Turned Off Inlet Valve FailedHardware Output Test Diagnostic ModesTub Home Sensor Test Fast Test CycleResistance Checks Troubleshooting ChartWiring Diagram Page United States Product Specifications Warranty Information Sources