KitchenAid KAD-9 manual General, Safety First

Page 5

GENERAL

SAFETY FIRST

Your safety and the safety of others is very important.

We have provided many important safety messages in this Job Aid and on the appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don’t immediately follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

1-1

Image 5
Contents Drawer Dishwasher Goals and Objectives ForwardTable of Contents Diagnostics & Troubleshooting General Safety FirstModel Number Model & Serial Number DesignationsSerial Number D D 01 D P PAModel & Serial Number Label Tech Sheet Locations General SpecificationsKitchenAid will not pay for Kitchenaid Dishwasher WarrantyTWO-YEAR Full Warranty Page Parts Supplied GeneralTools and Material Required 32-3/16 34-1/2 Cm 87.8 cm Product DimensionsFrom front Cabinet Dimensions / RequirementsWater Requirements Electrical RequirementsRecommended Ground Method Foragrounded,cord-connecteddishwasherPower Supply Cord Installing the DishwasherSide Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installationsStandard Toe Kick Front Panels & TOE KickStandard Front Panels Toe kick Custom Front Panels Custom Front Panels DimensionsLay the custom front panel face down Custom Toe Kick Custom Toe Kick DimensionsSystem Overview Filter Plate Drain CycleDrying Cycle LID SystemControl Panels Parts and FeaturesWash System To Clean The Spray ArmDishwasher Systems To Clean The Filter Plate To Clean The Drain FilterSound System Drying SystemFilling The Powdered Detergent Dispenser Using the DishwasherDetergent USE Program Quantities How Much Detergent To UseRinse AID Dispenser Rinse Aid IndicatorFilling The Dispenser How Much Rinse Aid To UsePerformance Tips Wash Programs Program ChartsPausing a Cycle Canceling a Wash CycleChanging a Cycle Or Setting Option Selections AdjustmentsTo enter the Option Adjustment Mode Delay Start ModeTo adjust the Rinse Aid setting Control LockTo disable the End of Wash Program beeps To disable the Auto PowerPage In-Tub Components Component LocationsTub-Mounted Components Cabinet-Mounted ComponentsRemoving the Spray ARM and Impeller On the next Removing the ISOLATOR, BADGE, & Door HandleTo remove the isolator Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors To remove the chassis module Removing the Chassis Module and Power CordTo remove the power cord Removing the Water Fill Valves Drying FAN Component TestingWash & Drain Motor Rinse AID and Detergent DispenserTo test the heater, touch the ohmmeter Power Resistor & HeaterLID Motor Water Fill Valves Temperature SensorError Code Display Mode DiagnosticsError Codes Bad Wiring Or Connections Temperature Sensor FailedMoisture / Foreign Matter On Chassis Board Flood Switch PCB Failed Heater ElementWiring Or Connections Bad Moisture Around Temperature SensorWater Supply Valve Turned Off Inlet Valve FailedHardware Output Test Diagnostic ModesTub Home Sensor Test Fast Test CycleResistance Checks Troubleshooting ChartWiring Diagram Page United States Product Specifications Warranty Information Sources