KitchenAid KAD-9 Removing the ISOLATOR, BADGE, & Door Handle, To remove the isolator, On the next

Page 45

REMOVING THE ISOLATOR, BADGE, & DOOR HANDLE

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug dishwasher or disconnect power.

2.Open the dishwasher drawer.

3.Using a pair of longnosed pliers, pull out and remove the left and right pins from the tub. NOTE: Keep the pin web in the verti- cal position when you reinstall the pin in the tub.

Side Of Tub

Pin

4.Pull the drawer front down so it is free of the handle and the top locating slots and remove the front.

5.To remove the isolator:

a)Disconnect the two green ground wires from the inner door panel, and the badge connector from the isolator connector.

b)Remove the isolator from the front of the dishwasher.

Ground Wires

Badge & Isolator

Connectors

Isolator

c)Disconnect the two wire connectors from the isolator.

Isolator

Connector

Connector

(Blue Wires)

(White Wires)

Continued on the next page.

4-3

Image 45
Contents Drawer Dishwasher Goals and Objectives ForwardTable of Contents Diagnostics & Troubleshooting General Safety FirstModel Number Model & Serial Number DesignationsSerial Number D D 01 D P PAModel & Serial Number Label Tech Sheet Locations General SpecificationsKitchenaid Dishwasher Warranty TWO-YEAR Full WarrantyKitchenAid will not pay for Page General Tools and Material RequiredParts Supplied 32-3/16 34-1/2 Cm 87.8 cm Product DimensionsFrom front Cabinet Dimensions / RequirementsWater Requirements Electrical RequirementsRecommended Ground Method Foragrounded,cord-connecteddishwasherPower Supply Cord Installing the DishwasherSide Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installationsFront Panels & TOE Kick Standard Front PanelsStandard Toe Kick Toe kick Custom Front Panels Custom Front Panels DimensionsLay the custom front panel face down Custom Toe Kick Custom Toe Kick DimensionsSystem Overview Filter Plate Drain CycleDrying Cycle LID SystemControl Panels Parts and FeaturesTo Clean The Spray Arm Dishwasher SystemsWash System To Clean The Filter Plate To Clean The Drain FilterSound System Drying SystemUsing the Dishwasher Detergent USEFilling The Powdered Detergent Dispenser Program Quantities How Much Detergent To UseRinse AID Dispenser Rinse Aid IndicatorFilling The Dispenser How Much Rinse Aid To UsePerformance Tips Wash Programs Program ChartsPausing a Cycle Canceling a Wash CycleChanging a Cycle Or Setting Option Selections AdjustmentsTo enter the Option Adjustment Mode Delay Start ModeTo adjust the Rinse Aid setting Control LockTo disable the End of Wash Program beeps To disable the Auto PowerPage In-Tub Components Component LocationsTub-Mounted Components Cabinet-Mounted ComponentsRemoving the Spray ARM and Impeller Removing the ISOLATOR, BADGE, & Door Handle To remove the isolatorOn the next Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors Removing the Chassis Module and Power Cord To remove the power cordTo remove the chassis module Removing the Water Fill Valves Drying FAN Component TestingWash & Drain Motor Rinse AID and Detergent DispenserPower Resistor & Heater LID MotorTo test the heater, touch the ohmmeter Water Fill Valves Temperature SensorError Code Display Mode DiagnosticsError Codes Bad Wiring Or Connections Temperature Sensor FailedMoisture / Foreign Matter On Chassis Board Flood Switch PCB Failed Heater ElementWiring Or Connections Bad Moisture Around Temperature SensorWater Supply Valve Turned Off Inlet Valve FailedHardware Output Test Diagnostic ModesTub Home Sensor Test Fast Test CycleResistance Checks Troubleshooting ChartWiring Diagram Page United States Product Specifications Warranty Information Sources