Frymaster BIGLA30 warranty BI-WEEKLY Checks and Service, Check M3000 Computer Set Point Accuracy

Page 75
Blower
assembly
mounting nuts

Wipe the filter pan and all detachable parts and accessories with a clean dry cloth. Use a cloth dampened with a solution of McDonald’s All Purpose Concentrate to remove accumulated carbonized oil. Rinse and thoroughly dry each part. DO NOT use steel wool or abrasive pads to clean these parts. The scratches that result from such scrubbing make subsequent cleanings more difficult.

6.4BI-WEEKLY CHECKS AND SERVICE

6.4.1 Check M3000 Computer Set Point Accuracy

1.Insert a good-grade thermometer or pyrometer probe into the oil, with the end touching the fryer temperature- sensing probe.

2.When the computer display shows a series of dashes “----” or a product name (indicating that the frypot

contents are within the cooking range), press the switch once to display the temperature of the oil as sensed by the temperature probe.

3.Press the switch twice to display the set point.

4.Note the temperature on the thermometer or pyrometer. Actual temperature and pyrometer readings should be within ± 5ºF (3ºC) of each other. If not, contact a Factory Authorized Service Agency for assistance.

6.5QUARTERLY CHECKS AND SERVICE

6.5.1 Clean Combustion Air Blower Assembly

1. Disconnect the blower wiring harness and remove the four blower mounting nuts. (See Figure 1 on below)

Wiring connection

Figure 1

2.Remove the three fasteners that secure the blower motor assembly to the blower housing, and separate the two components. (See Figure 2)

Remove these fasteners.

Figure 2

6-3

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Manufactured Canada Page LOV GAS Warranty Statement Parts Return General Safety InformationInstallation, Operating, and Service Personnel Computer Information for the M3000 ComputersEuropean Community CE Specific Information Qualified Installation Personnel Qualified Service PersonnelQualified AND/OR Authorized Operating Personnel Retain and Store this Manual in a Safe Place for Future USE Clearance and Ventilation General Installation RequirementsElectrical Grounding Requirements National Code RequirementsCaster Installation Non-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Single Dual Gas Vat Converting to Another Gas TypeCE GAS Conversion Instructions Non-CE Gas Conversion KitsNon-CE Gas Conversion Kits for Australia CE Gas Conversion Kits for Units with Gas ValveAfter Fryers are Positioned at the Frying Station BIGLA30 Series GEN II LOV GAS Fryer Operating Instructions Typical Configuration BIGLA330 ShownPage Lighting the Fryer Press the computer ON/OFF switch to the OFF positionOperation ShutdownChanging the JIB Low Oil Volume Automatic RefillInstall the JIB Prepare the System for UseFront of the fryer off see Figure M3000 General Information FR FriesBasic Operation Cooking with Multi-Product Display Cooking with Dedicated Display Changing from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast Cook Channel and Selection Buttons Filter, Temperature and Info ButtonsM3000 Button Description and Functions Navigation ButtonsDraining, Refilling, and Disposing of Oil M3000 Menu Summary Tree1234 Fryer Setup Mode Programming24hR 10 M3000 Common Tasks Escape Menu ItemsFull Prod Adding New Product Items to the Menu Product SelectionSelection ProductCook ID Disable Storing Menu Items in Product Buttons Product selection promptTo Level 1 program changing to the Product selection Disposal for Non-Bulk Oil Systems Draining and Refilling Vats, and Disposing of OilRefilling JIB Oil Systems Draining and Disposing Oil using Bulk Oil SystemsPage Refilling the Vat from Bulk Oil Systems after Disposal Accessing the Filter MenuDrain to Pan Yes no Fill Vat from Drain PanFill Vat from Bulk Pan to Waste Programming Level OneAIF Clock Selection display Deep Clean Mode BOIL-OUTEMPTY? and Yes no PANPage HIGH-LIMIT Test Mode Comp Programming Level TwoLevel 2 Program Product Comp ModePassword Setup Mode LOG ModeAlert Tone Mode Filter After Filter Time Info ModeFilter Stats Mode Full VAT ConfigurationSplit VAT Configuration DAY wed, Date 03/20/07 Current day and date Review Usage ModeLast Load Mode Full / Split VAT Configuration4321 Page Introduction BIGLA30 Series GEN II LOV GAS Fryer Filtration InstructionsDo not USE Filter Powder with the PAD Auto Demand Filtration DRAINING, Washing and Filling during the processPage Clogged Drain Error FIXED? YES no is displayed Filter Error FlowchartSystem Error Normal Operation ResumesClogged Drain or Oil Sensor Fail Flowchart Filter Busy Page Page Clean Fryer Cabinet Inside and Out Daily Fryer Preventive Maintenance Checks and ServiceDaily Checks and Service Inspect Fryer and Accessories for DamageClean Filter Pan, Detachable Parts and Accessories Weekly Checks and Service 6.3.1 Clean Behind FryersCleaning the Frypot Quarterly Deep Clean Boiling Out the FrypotCheck M3000 Computer Set Point Accuracy BI-WEEKLY Checks and ServiceQuarterly Checks and Service Clean Combustion Air Blower AssemblyLeft Viewing PortRight Port is Behind Motor Fryer Clean Oil Level SensorReplace the O-RINGS Annual/Periodic System InspectionBuilt-In Filtration System BIGLA30 Series GEN II LOV GAS Fryer Operator Troubleshooting Change Filter Service Auto Top Off Problems Probable Causes Corrective Action Explanation ProblemError Drain Valve not Closed Used oil to a JIB Bulk Oil SystemsService Hotline
Related manuals
Manual 88 pages 5.79 Kb Manual 26 pages 13.97 Kb

BIGLA30 specifications

The Frymaster BIGLA30 is a state-of-the-art commercial frying solution designed to meet the high demands of busy food service environments. Known for its energy efficiency, reliability, and advanced technology, the BIGLA30 has become a favorite among restaurateurs and catering businesses.

One of the standout features of the BIGLA30 is its large capacity. With a significant oil capacity, it allows for frying large quantities of food simultaneously, making it ideal for high-volume establishments. This capacity enables kitchens to keep up with demand during peak hours, ensuring that orders are fulfilled quickly and efficiently.

The Frymaster BIGLA30 is equipped with advanced digital controls that simplify the frying process. The intuitive interface allows operators to easily adjust cooking times and temperatures, ensuring consistent results. The digital controls are also equipped with a filtration system that automatically cleans the oil, which prolongs its life and ensures the food maintains optimal flavor.

Another prominent feature of the BIGLA30 is its energy-efficient design. It utilizes innovative heating technology that reduces energy consumption while providing high-performance frying. This not only helps to lower operational costs but also supports environmentally friendly practices within the kitchen.

Safety is paramount in any commercial kitchen, and the BIGLA30 excels in this area. It is designed with safety mechanisms such as automatic shut-off and temperature control systems to prevent overheating. Additionally, the unit features large, easy-to-grip handles on pots, allowing for safe handling and transfer of food items.

In terms of construction, the Frymaster BIGLA30 is built with high-quality materials that ensure durability and longevity. The robust design can withstand the rigors of a busy kitchen and is easy to maintain, reducing downtime and service costs. Its sleek stainless-steel exterior not only presents a professional aesthetic but is also simple to clean, contributing to overall kitchen hygiene.

Furthermore, the BIGLA30 is compatible with various cooking applications, making it versatile enough to fry a wide range of items from crispy fries to delicious chicken. This adaptability makes it a valuable addition to any food service operation.

In summary, the Frymaster BIGLA30 is a top-tier frying solution that combines capacity, energy efficiency, advanced technology, and safety features. Its ability to deliver consistent results while minimizing costs makes it an essential tool for any commercial kitchen.
Top Page Image Contents