Frymaster Y/KSCF/C/HC18G operation manual Gas Connections

Page 17

Y/KSCF/C/HC18G HIGH EFFICIENCY COOL ZONE SERIES GAS FRYERS

CHAPTER 3: INSTALLATION INSTRUCTIONS

3.3 Leveling the Fryer (cont.)

ANSI Z83.11/11a-(Latest Edition) requires a fryer be restrained to prevent tipping when installed in order to avoid the splashing of hot liquid. The means of restraint may be the manner of installation, such as connection to battery of appliances or installing the fryer in an alcove, or by separate means, such as adequate ties (chains, straps, etc.). A bracket has been provided on the fryer back panel for this purpose.

NOTE: The installation must be inspected after it is complete to ensure it meets the intent of these instructions. The on-site supervisor and/or operator(s) should be informed that the appliance is installed with restraints. If restraints are removed to move fryer (e.g., to clean beneath and behind, to relocate) ensure that they are re-installed when fryer is returned to its permanently installed position.

For information on fryer restraints, see Section 2.8.

3.4 Gas Connections

The gas supply (service) line must be the same size or greater than the fryer inlet line. YSCFH18G gas fryers are equipped with a ¾-inch (22-mm) male inlet. The gas supply line must be sized to accommodate all gas-fired equipment connected to that gas supply. Consult local gas companies/suppliers or your local contractor for minimum supply line requirements.

Supply Line Specifications

The gas supply lines must be sized as indicated in the chart below, based on the total number of fryers connected to the main gas supply.

Recommended Gas Supply Line Sizes

Gas Types

Number of Fryers

 

 

 

1

2 to 3

4 or more*

Natural Gas

¾" (22 mm)

1" (28 mm)

1¼ " (35 mm)

Propane Gas

½" (15 mm)

¾" (22 mm)

1" (28 mm)

*When exceeding 18 feet (6 meters) for a configuration of more than four fryers, it is necessary to provide a 1¼" (35 mm) rigid gas connection.

DANGER

All connections must be sealed with a joint compound suitable for the gas being used and all connections must be tested with a solution of soapy water before lighting any pilots.

Never use matches, candles, or any other ignition source to check for leaks. If gas odors are detected, shut off the gas supply to the appliance at the main shut-off valve and immediately contact the local gas company or an authorized service agency for service.

3-4

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 8196329 Page Page KSCF/C/HC18G Cool Zone Gas Fryers Ordering Parts After PurchaseController Information Service InformationSafety Information Safety Information Service Personnel If your equipment arrives damaged Receiving and Unpacking EquipmentGeneral Rating Plate Pre-InstallationPrinciples of Operation ANSI/NFPA #70 Australian installations must meetAir Supply and Ventilation Equipment Installed at High AltitudesRestraining the Fryer Page General Installing the FryerLeg and Caster Installation Leveling the Fryer InstallationRigid Casters Only Installing Optional Swivel CastersLegs Only Gas Connections Regulating Gas Pressure Rigid ConnectionsManual Shut-off Valve Flexible Couplings, Connectors and Casters Adjustments/Adaptation To Different Gases GAS Supply for Which IT is not Configured Gas Conversion ProceduresFryer with KFC-1 Computer Safety SwitchesElectrical Connections Microswitch is located on the red handle at the drain valve Return system Final Preparation Initial Cleaning Before StartupDrop General Use Start-Up ProceduresPilot lighting procedures Standing Pilot Pilot lighting procedure Electronic Ignition Closing See for detailed filtration proceduresFiltering Filter Powder Filter Paper Filter PreparationFilter Preparation Page Filter Operations Remove large debris floating in the oil Removing support grid from frypot prior to draining Filter Operations Filter Operations Page Weekly DailyBuilt-in Filtration Periodic/AnnualStainless Steel Periodic/ AnnualIntroduction Pressed Fryer TroubleshootingCont Burner Tube Remains after closing drain Main burner malfunctions Pump wont Start Filtration System TroubleshootingWiring Diagrams Fast controller Non-CE Fast Controller CE Fast Controller India KFC-1 Controller This page Intentionally Left Blank Service Hotline

Y/KSCF/C/HC18G specifications

The Frymaster Y/KSCF/C/HC18G is a modern deep fryer designed for high volume cooking, particularly suited for the fast-paced demands of commercial kitchens. With its robust engineering and innovative technologies, this fryer delivers exceptional performance, ensuring efficiency and consistency in food quality.

One of the standout features of the Frymaster Y/KSCF/C/HC18G is its high-capacity frying capability. Designed to accommodate large batches, it can hold significant amounts of oil, allowing for the frying of various foods simultaneously, thus optimizing cooking times. This fryer is ideal for establishments that requires consistent output, such as restaurants, cafeterias, and food trucks.

The Y/KSCF/C/HC18G incorporates advanced oil filtration technology, which is crucial for maintaining the quality of the frying oil over extended periods. This system automatically filters oil during idle times and prior to cooking cycles, removing food particles and prolonging the life of the oil, ultimately leading to cost savings for businesses. The filtration process also contributes to better-tasting foods by reducing the build-up of unwanted residues.

Another innovative characteristic of this fryer is its precise temperature control. The Frymaster Y/KSCF/C/HC18G utilizes a digital control system that allows operators to set and monitor cooking temperatures accurately. This feature helps achieve optimal frying conditions for different food types, ensuring that items are cooked evenly and to the desired crispness.

Energy efficiency is another important aspect of the Frymaster Y/KSCF/C/HC18G. Equipped with high-performing heating elements, this fryer heats up quickly and maintains temperature consistently, reducing energy consumption. Features such as programmable cook times and automatic shut-off further enhance energy efficiency, contributing to lower operational costs.

Safety is paramount in commercial kitchens, and the Frymaster Y/KSCF/C/HC18G is designed with multiple safety features. It includes an automatic safety shut-off system that activates if the fryer reaches dangerously high temperatures, thereby preventing overheating and potential hazards.

In summary, the Frymaster Y/KSCF/C/HC18G is an outstanding deep fryer that combines high capacity, efficient oil filtration, precise controls, energy-saving features, and robust safety mechanisms. It is an ideal choice for operators seeking reliability and excellence in their frying operations, ensuring that they can meet customer demands without compromising on quality.
Top Page Image Contents