Frymaster FPHD manual Probe cannot be repositioned

Page 19

HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS

CHAPTER 1: SERVICE PROCEDURES

1.7.3 Replacing the Temperature Probe; Computer-equipped Fryers (cont.)

10.Locate the temperature probe inside the frypot. Remove the temperature probe mounting hardware. Retain mounting hardware for installation of new temperature probe.

Locate the temperature probe.

11.The temperature probe can be removed through the bottom of the frypot as follows: Ensure the two-pin connector has been removed from the probe wiring harness (step 4, above). Remove the harness insulation. The probe can be pulled through the frypot from the bottom (complete step 7, above, prior to removing probe).

12.Carefully remove the probe from the frypot. As the probe is removed, tilt the probe at an angle to facilitate removal (curved probes only).

13.Follow the steps on the next page to install the new temperature probe.

IMPORTANT: When installing new probe, use Loctite PST567 or equivalent pipe thread sealant on threads and ensure probe is positioned properly with the mounting hardware installed prior to tightening the compression nut. Once tightened,

the probe cannot be repositioned.

After removing the probe mounting hardware, the temperature probe can be removed through the bottom of the frypot. Retain the mounting hardware for reassembly.

1-14

Image 19

Contents Includes HD63/Red Robin and Common Cabinetry Hour Service HotlineMAY Page Computers FCC Table of Contents Page GAS Information Altitudes of 2000 feet or less Functional DescriptionElectronic Ignition Configuration Pilot System ConfigurationInterface Boards Control OptionsThermatron Board P/N Interface Boards Indicates power from 12V transformer Test Meter Setting Pins Test ResultsThermostats Accessing Fryers for ServicingRestraints Adjusting Burner Manifold Gas Pressure Cleaning the Gas Valve Vent Tube if applicableTrailing Pilot Adjusting the Pilot FlameCalibrating the Thermatron Main PilotReplacing the Computer Replacing Fryer ComponentsReplacing the Temperature Probe Computer-equipped Fryers Replacing the Temperature Probe Computer-equipped Fryers Probe cannot be repositioned Replacing the High-limit Thermostat Installing the New Temperature ProbeLocate the high-limit probe Capillary tube cannot be repositioned Figure B Replacing Rocker SwitchesReplacing Rocker Switches Replacing the Frypot Replacing the Pilot AssemblyRemoving the joiner strip Removing gas manifold shield Removing bolts arrows securing flue to frypot Nut Valve Boot Clamp Remove the drain valve nut and attached Hardware Cutting frypot seal prior to frypot removal Lifting frypot from fryer Ignition Failure Troubleshooting and Problem IsolationImproper Burner Function Electronic CircuitsImproper Burner Function Improper Temperature Control Improper Computer Function Improper Filtration Function Frypot Leakage Improper Basket Lift Function Bell-Crank Basket Lifts Problem Troubleshooting GuidesNot possible High Efficiency Decathlon, Thermatron with Constant Pilot Wiring DiagramsRight/left sides are the same Computer with Constant Pilot CM4-S Wiring Dean Oil Return Wiring Dean Oil Return Wiring, with Solenoid Probe Resistance Charts High Efficiency Decathlon HD Primary Components High Efficiency Decathlon Series GAS Fryers Parts ListSee Orifices, Section Decathlon HD50 Primary Components includes Scfhd unitsSee Drain Manifold Components, Section Decathlon HD50 Primary Components includes Scfhd units 823-4692 Decathlon HD60 Primary Components includes Scfhd unitsFlue Box Assembly also used on HD63 fryers Front, Flue Box Decathlon FPHD65 Primary Components Cabinet Upper Back Channel, Base 265 465 565Cabinet Lower Back Door Assembly, with Liner also used for HD63 fryers Natural Orifices OrificesPropane Orifices Joiner Strips Control Panel Options, Joiner Strips, and AccessoriesAccessories Control PanelsOptional Components and Controllers HD/SCFHD50 SCFHD456 SCFHD60 BezelsInterface Boards High Efficiency Decathlon Series GAS Fryers Parts List Drain Valve Assembly, 1 1 ⁄ 2 with Microswitch Drain Valve Assembly, 1 1 ⁄ 2 without MicroswitchFlush Oil Drain Line Oil Return Manifold Components Oil Return Manifold Components Oil Return Manifold Components Oil Return and Oil Flush Components Oil Suction Start Fitting Microswitch Bracket Assembly, Oil ReturnOil Suction Assembly Suction Manifold AssemblyDescription 106-7543 Filtration Components SCFHD60 and SCFHD63 Series FryersFiltration Components FPHD65 Series Fryers Basket Lift Components Basket Lift Components Trough, Holster, & Cover Components Fasteners Screws, Nuts, Bolts Service Hotline