Frymaster MPH55, BIPH55 warranty National Code Requirements, Electrical Grounding Requirements

Page 12

DANGER

No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call the Frymaster Dean Service Hotline at 1-800-551-8633.

One of the most important considerations of efficient fryer operation is ventilation. Make sure the fryer is installed so that products of combustion are removed efficiently, and that the kitchen ventilation system does not produce drafts that interfere with burner operation.

The fryer flue opening must not be placed close to the intake of the exhaust fan, and the fryer must never have its flue extended in a “chimney” fashion. An extended flue will change the combustion characteristics of the fryer, causing longer recovery time. It also frequently causes delayed ignition. To provide the airflow necessary for good combustion and burner operation, the areas surrounding the fryer front, sides, and rear must be kept clear and unobstructed.

DANGER

This appliance must be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to the health of personnel in the room in which it is installed.

Fryers must be installed in an area with an adequate air supply and adequate ventilation. Adequate distances must be maintained from the flue outlet of the fryer to the lower edge of the ventilation filter bank. Filters should be installed at an angle of 45º. Place a drip tray beneath the lowest edge of the filter. For U.S. installation, NFPA standard No. 96 states, “A minimum distance of 18 in. (450 mm) should be maintained between the flue outlet and the lower edge of the grease filter.” Frymaster recommends that the minimum distance be 24 in. (600 mm) from the flue outlet to the bottom edge of the filter when the appliance consumes more than 120,000 BTU per hour.

For installations in the United States, information on construction and installation of ventilating hoods can be found in the NFPA standard cited above. A copy of the standard may be obtained from the National Fire Protection Association, Battery March Park, Quincy, MA 02269.

2.1.2 NATIONAL CODE REQUIREMENTS

The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of the fryer door. Connect a fryer stamped “NAT” only to natural gas, those stamped “PRO” only to propane gas, and those stamped “MFG” only to manufactured gas.

Installation shall be made with a gas connector that complies with national and local codes, and, where applicable, CE codes. Quick-disconnect devices, if used, shall likewise comply with national, local, and, if applicable, CE codes.

2.1.3 ELECTRICAL GROUNDING REQUIREMENTS

All electrically operated appliances must be grounded in accordance with all applicable national and local codes, and, where applicable, CE codes. All units (cord connected or permanently connected) should be connected to a grounded power supply system. A wiring diagram is located on the inside of the fryer door. Refer to the rating plate on the inside of the fryer door for proper voltages.

2-2

Page 11 Page 13
Image 12
Page 11 Page 13
Contents For Your Safety OPERATOR’S Manual Frymaster BIPH55/MPH55 Series GAS FryerCanada Page Warranty Statement Warranty Provisions Cooking Computer BIPH55 / MPH55 Series GAS Fryer Introduction GeneralSafety Information Computer Information for the M2000 ComputersQualified Installation Personnel Qualified Service PersonnelQualified AND/OR Authorized Operating Personnel Shipping Damage Claim Procedure Parts Ordering and Service InformationWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE BIPH55 / MPH55 Series GAS Fryer Installation Instructions General Installation RequirementsClearance and Ventilation Do not block the area around the base or under the fryersNational Code Requirements Electrical Grounding RequirementsCaster Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Single Dual Gas VatNon-CE Gas Conversion Kits CE GAS Conversion Instructions After the Fryers Are Positioned At the Frying StationTypical Configuration BIPH255 Shown BIPH55 / MPH55 Series GAS Fryer Operating InstructionsFinding Your WAY around the BIPH55 Series GAS Fryer Page Press the computer ON/OFF switch to the OFF position Lighting the FryerWhen shutting the fryers down at closing time ShutdownFor short-term shut down during the workday Boiling Out the FrypotBIPH55 / MPH55 Series GAS Fryer Filtration Instructions IntroductionScreen Filter Pad or Filter Paper Crumb Tray Hold-Down Ring Do not use filter powder with the pad Filter Pump Reset Switch Page BIPH55 / MPH55 Series GAS Fryer Preventive Maintenance Daily Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutWeekly Checks and Service 5.3.1 Clean Behind Fryers Monthly Checks and Service Check M2000 Computer Set Point AccuracyBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Fryer Built-In Filtration System BIPH55 / MPH55 Series GAS Fryer Operator Troubleshooting Before calling a servicer or the Frymaster HotlineTroubleshooting Fryers Computer and Heating Problems Problem Probable Causes Corrective ActionError Messages and Display Problems Shows LOW Temp FailureShows Ignition Shows HI-LIMITTroubleshooting the Built-in Filtration System Shows HI 2 BADFrom PreviousFilter Pump starts But no transfer takesReplacing the Controller or Controller Wiring Harness BackThis page Intentionally Left Blank 819-6087

BIPH55, MPH55 specifications

The Frymaster BIPH55 and MPH55 are cutting-edge fryers designed to meet the needs of modern commercial kitchens. Renowned for their efficiency and reliability, these fryers are perfect for establishments looking to optimize their frying processes, ensuring that food is cooked to perfection while minimizing oil use and maximizing output.

One of the main features of the Frymaster BIPH55 and MPH55 is their innovative oil filtration system. This technology allows for continuous oil filtration during operation, which not only enhances the lifespan of the oil but also maintains food quality. The built-in filtration system reduces the need for manual oil changes, saving both labor and costs while delivering crispier, more delicious fried products.

Additionally, the BIPH55 model is designed with a high-efficiency burner system that reduces energy consumption, making it an eco-friendly choice. This system increases cooking speeds and provides precise temperature control, which is critical for achieving consistent results. The adjustable temperature settings allow chefs to customize their frying processes to suit various types of cuisine, from crispy French fries to succulent chicken wings.

Another standout characteristic of these fryers is their digital control interface. The user-friendly display allows operators to monitor cooking times and temperatures easily, reducing the risk of human error. Programmable controls can store up to 12 menu items, allowing for quick access to settings tailored for specific recipes, thus enhancing efficiency during peak hours.

The durable construction of the Frymaster BIPH55 and MPH55 ensures a long lifespan, even in the busiest kitchens. The stainless steel body is easy to clean and resistant to corrosion, which is essential for maintaining hygiene standards. The fry baskets are designed to be lightweight yet robust, allowing for easy handling while ensuring that food items can be submerged without difficulty.

Safety features are also a priority in these models, with automatic shut-off mechanisms that prevent overheating and ensure safe operation. The design includes a large oil capacity, which is ideal for high-volume frying operations, allowing establishments to serve their customers promptly without sacrificing quality.

In conclusion, the Frymaster BIPH55 and MPH55 are superb additions to any commercial kitchen looking to enhance their frying capabilities. With a combination of advanced technologies, robust construction, user-friendly controls, and energy efficiency, these fryers represent an investment in quality cooking and operational excellence. Whether for a fast-food outlet, restaurant, or catering service, the BIPH55 and MPH55 are poised to elevate the frying experience.
Top Page Image Contents