Frymaster E4 manual Replacing a Heating Element

Page 10

10.Secure any loose wires with wire ties making sure that the lead wires will not interfere with the movement of the springs. Rotate the elements up and down making sure that movement is not restricted and that the wires are not pinched.

11.Reinstall the tilt housing and back panels, reposition the fryer under the exhaust hood, and reconnect it to the electrical power supply to return the fryer to service.

1.6Replacing a Heating Element

1.Perform steps 1-3 of section 1.5, Replacing a Temperature Probe.

2.On dual-vat fryers, and on full-vat fryers where the temperature probe is attached to the element being replaced, disconnect the wire harness containing the probe wiring. Using a pin pusher, disconnect the probe wires from the 12-pin connector C-6.

3.In the rear of the fryer directly behind the frypot disconnect the 6-pin connector for the left element (as viewed from the front of the fryer) or the 9-pin connector for the right element. Press in on the tabs on each side of the connector while pulling outward on the free end to extend the connector and release the element leads (see photo below). Pull the leads out of the connector and out of the wire sleeving.

4.Raise the element to the full up position and support the elements.

5.Remove the hex head screws and nuts that secure the element to the tube assembly and pull the element out of the frypot. NOTE: Full-vat elements consist of two dual-vat elements clamped together. For full-vat units, remove the element clamps before removing the nuts and screws that secure the element to the tube assembly.

6.If applicable, recover the probe bracket and probe from the element being replaced and install them on the replacement element. Install the replacement element in the frypot, securing it with the nuts and screws removed in Step 5 to the tube assembly. Ensure the gasket is between the tube and element assembly.

7.Route the element leads through the element tube assembly and into the wire sleeving to prevent chafing. Ensure that the wire sleeving is routed back through the Heyco bushing keeping it clear

1-5

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Hour Service Hotline RE Series Electric FryersPage Electrical Power Specifications RE Series E4 Electric Fryers Table of Contents RE Series E4 Electric Fryers Replacing a Controller GeneralReplacing Component Box Components Removing the Control Panel Frame and Top Cap Assembly Replacing a Temperature Probe Replacing a High-Limit ThermostatPage Replacing a Heating Element Replacing Contactor Box Components Replacing a Frypot Page Right Sediment Particle Oil Flow Up for reverse Down for forward Disconnect flexlines indicated by the arrows Basket Lift Service Procedures Replacing the Filter Transformer or Filter RelayBINDING/JAMMING Problems Motor and Gear Problems Interface Board Diagnostic Chart Diagnostic LED LegendProbe Resistance Chart Probe Resistance ChartWiring Diagrams Modular Basket Lift Wiring Diagram Modular Basket Lift Wiring Diagram Component Wiring Standard Fryers Component Wiring- Fryer and Half Tilt Switch Wiring Standard Fryer and half Component Wiring Fast Ready Fast Ready Computer Wiring Computer Harness Fast Ready Control Wiring Fast Ready Contactor Delta Configuration Fryer and Half WiringContactor Box WYE Configuration Export Terminal Block Wiring Oil Disposal Wiring Simplified RE14/17/22 Wiring13.12 Series Full VatSimplified RE14/17/22 Series Dual Vat Wiring Electric RE14/17/22 Series FULL-VAT Export 13.14Simplified RE14/17/22 Series Dual Vat Wiring Export WYE Simplified RE14/17/22 Series Full Vat Wiring Epri Simplified RE14/17/22 Series Full Vat Wiring Epri Export WYE RE Series E4 Electric Fryers Parts List AccessoriesBasket Lift Assembly and Associated Parts 106-1805SP Page Single Station Fryer CRS Use 230-0422 for Stainless Steel Bezel, One-Controlleruse 230-1953 for Fryer ½ Cabinets, Bases, Braces, and Associated Parts Component See next section for Drain Valves Euro-Look Drain Tube Sections and Associated Parts PART# ComponentSingle Footprint Full-Vat Drain Valve Assembly 106-6300 Full-Vat Drain Valve Assembly Fryer ½ Compression Washers Page Drain Valves and Assoc. Parts Units with Built-In Filtration Valve, 1.25-inch Non-Filter Full-Vat Drain Electronics and Wiring Components 2.5.1 Component Boxes Component Boxes Page 807-2283 Contactor, 24V Page 807-2283 Contactor Fuse Boxes Cover, RH Fuse Box Used on Single Station Fryers alsoTerminal Blocks Page Heating Element Assemblies and Associated Parts Wire harnesses must2-30 for wire Be replaced whenElement Tube Assemblies Controllers Wiring Contactor Box Wiring Assemblies 12-Pin Dual-Vat C-1 Contactor Box Wiring Assemblies 12-Pin Full-Vat C-1 Contactor Box Wiring Assemblies 6-Pin Left Element Contactor Box Wiring Assemblies 9-Pin Right ElementMain Wiring Harnesses Full and Dual Vat Main Wiring Harnesses Fryer and ½ Component Box, Filter Pump and Basket Lift Wiring Harnesses Page Filtration System Components Roller Kit includes 4 rollers, 4 nuts and 4 lock washers √ Recommended parts Frypot Assemblies and Associated Parts Frypot Assembly does not include Item Oil Return System Components Typical Rear-Flush Oil Return PlumbingOil Return System Components Oil Disposal Plumbing Oil Disposal Wand Wiring Connectors and Pin Connectors Fasteners Service Hotline
Related manuals
Manual 2 pages 51.67 Kb Manual 36 pages 37.47 Kb Manual 78 pages 9.63 Kb

E4 specifications

The Frymaster E4 is an advanced fryer that represents the cutting edge of commercial frying technology. Designed for efficiency and performance, it is favored by restaurants and fast-food chains looking to optimize their cooking processes while maintaining exceptional food quality.

One of the standout features of the Frymaster E4 is its programmable controls. With an intuitive digital interface, operators can easily adjust cooking temperatures, times, and even recipes with just a few taps. This level of precision ensures that food is consistently cooked to perfection every time, reducing waste and improving overall efficiency in the kitchen.

The E4 is equipped with high-performance burners that ensure rapid heating and recovery times. This means that cooking oil reaches the desired temperatures quickly, allowing for faster frying cycles. Thus, busy kitchens can meet high-demand periods without compromising quality or service speed. The fryer also features a high-efficiency oil filtration system that automatically removes contaminants and prolongs the life of the frying oil, resulting in a significant reduction in operating costs over time.

Another notable technology in the Frymaster E4 is its oil level management system, which actively monitors oil levels and alerts the operator when replenishment is necessary. This feature prevents overfilling or underfilling, both of which can negatively impact cooking performance and food quality.

Safety is also a top priority with the E4, as it incorporates features such as a built-in safety shut-off mechanism that activates if the temperature exceeds safe levels. Additionally, the fryer's robust construction minimizes the risks of spills and accidents in the kitchen, making it a reliable choice for high-traffic environments.

The Frymaster E4 also emphasizes energy efficiency, designed to meet stringent energy-saving standards without compromising performance. This is crucial in the current market, where energy costs can significantly impact overall profitability.

In conclusion, the Frymaster E4 offers an impressive combination of innovative technology, safety, and efficiency. Its programmable controls, high-performance frying capabilities, and advanced filtration and oil management systems make it an essential tool for any commercial kitchen aiming to enhance productivity and food quality. As the demands of the food industry continue to grow, the E4 stands out as a reliable partner for chefs looking to elevate their frying operations.
Top Page Image Contents