Frymaster E4 Replacing the Filter Transformer or Filter Relay, Basket Lift Service Procedures

Page 17

10.Reconnect the unit to the electrical power supply, and verify that the pump is functioning correctly (i.e., when a filter handle is placed in the ON position, the motor should start and there should be strong suction at the intake fitting and outflow at the rear flush port.)

11.When proper operation has been verified, reinstall the back panels and the filter pan and lid.

12.Reposition the fryer under the exhaust hood and reconnect it to the electrical power supply to return the fryer to service.

1.9.3 Replacing the Filter Transformer or Filter Relay

Disconnect the fryer from the electrical power supply. Remove the left controller from the fryer to expose the interior of the left component box. The filter transformer and relay are located as shown in the illustration below. NOTE: The right component box is identical to the left except that the filter transformer and relay are not present. The components are held on by threaded pin studs so that only removal of the nut is required to replace the component.

Filter

Relay

Filter

Transformer

Dual-vat configuration illustrated. In full-vat units, left filter handle is not present.

1.10 Basket Lift Service Procedures

RE Series electric fryers may be equipped with automatic basket lifts. Basket lifts always come in pairs, although each operates independently.

A modular basket lift (illustrated on the following page) is a self-contained sub-assembly consisting of a pair of toothed rods which support removable basket lift arms, a pair of reversible- drive gear motors, and four microswitches. The gear motors engage the teeth of the rods, moving them up or down depending upon the motors’ direction of rotation. The microswitches at the upper and lower limits of movement stop the motors when the basket is in the full up or full down position.

1-12

Page 16 Page 18
Image 17
Page 16 Page 18
Contents RE Series Electric Fryers Hour Service HotlinePage Electrical Power Specifications RE Series E4 Electric Fryers Table of Contents RE Series E4 Electric Fryers Replacing Component Box Components GeneralReplacing a Controller Removing the Control Panel Frame and Top Cap Assembly Replacing a High-Limit Thermostat Replacing a Temperature ProbePage Replacing a Heating Element Replacing Contactor Box Components Replacing a Frypot Page Right Sediment Particle Oil Flow Up for reverse Down for forward Disconnect flexlines indicated by the arrows Replacing the Filter Transformer or Filter Relay Basket Lift Service ProceduresBINDING/JAMMING Problems Motor and Gear Problems Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartWiring Diagrams Modular Basket Lift Wiring Diagram Modular Basket Lift Wiring Diagram Component Wiring Standard Fryers Component Wiring- Fryer and Half Tilt Switch Wiring Standard Fryer and half Component Wiring Fast Ready Fast Ready Computer Wiring Computer Harness Fast Ready Control Wiring Fast Ready Fryer and Half Wiring Contactor Delta ConfigurationContactor Box WYE Configuration Export Terminal Block Wiring Oil Disposal Wiring 13.12 WiringSimplified RE14/17/22 Series Full VatSimplified RE14/17/22 Series Dual Vat Wiring 13.14 Electric RE14/17/22 Series FULL-VAT ExportSimplified RE14/17/22 Series Dual Vat Wiring Export WYE Simplified RE14/17/22 Series Full Vat Wiring Epri Simplified RE14/17/22 Series Full Vat Wiring Epri Export WYE Accessories RE Series E4 Electric Fryers Parts ListBasket Lift Assembly and Associated Parts 106-1805SP Page Single Station Fryer CRS Use 230-0422 for Stainless Steel Bezel, One-Controlleruse 230-1953 for Fryer ½ Cabinets, Bases, Braces, and Associated Parts Component See next section for Drain Valves PART# Component Euro-Look Drain Tube Sections and Associated PartsSingle Footprint Full-Vat Drain Valve Assembly 106-6300 Full-Vat Drain Valve Assembly Fryer ½ Compression Washers Page Drain Valves and Assoc. Parts Units with Built-In Filtration Valve, 1.25-inch Non-Filter Full-Vat Drain Electronics and Wiring Components 2.5.1 Component Boxes Component Boxes Page 807-2283 Contactor, 24V Page 807-2283 Contactor Cover, RH Fuse Box Used on Single Station Fryers also Fuse BoxesTerminal Blocks Page 2-30 for wire Wire harnesses mustHeating Element Assemblies and Associated Parts Be replaced whenElement Tube Assemblies Controllers Wiring Contactor Box Wiring Assemblies 12-Pin Dual-Vat C-1 Contactor Box Wiring Assemblies 12-Pin Full-Vat C-1 Contactor Box Wiring Assemblies 9-Pin Right Element Contactor Box Wiring Assemblies 6-Pin Left ElementMain Wiring Harnesses Full and Dual Vat Main Wiring Harnesses Fryer and ½ Component Box, Filter Pump and Basket Lift Wiring Harnesses Page Filtration System Components Roller Kit includes 4 rollers, 4 nuts and 4 lock washers √ Recommended parts Frypot Assemblies and Associated Parts Frypot Assembly does not include Item Typical Rear-Flush Oil Return Plumbing Oil Return System ComponentsOil Return System Components Oil Disposal Plumbing Oil Disposal Wand Wiring Connectors and Pin Connectors Fasteners Service Hotline
Related manuals
Manual 2 pages 51.67 Kb Manual 36 pages 37.47 Kb Manual 78 pages 9.63 Kb

E4 specifications

The Frymaster E4 is an advanced fryer that represents the cutting edge of commercial frying technology. Designed for efficiency and performance, it is favored by restaurants and fast-food chains looking to optimize their cooking processes while maintaining exceptional food quality.

One of the standout features of the Frymaster E4 is its programmable controls. With an intuitive digital interface, operators can easily adjust cooking temperatures, times, and even recipes with just a few taps. This level of precision ensures that food is consistently cooked to perfection every time, reducing waste and improving overall efficiency in the kitchen.

The E4 is equipped with high-performance burners that ensure rapid heating and recovery times. This means that cooking oil reaches the desired temperatures quickly, allowing for faster frying cycles. Thus, busy kitchens can meet high-demand periods without compromising quality or service speed. The fryer also features a high-efficiency oil filtration system that automatically removes contaminants and prolongs the life of the frying oil, resulting in a significant reduction in operating costs over time.

Another notable technology in the Frymaster E4 is its oil level management system, which actively monitors oil levels and alerts the operator when replenishment is necessary. This feature prevents overfilling or underfilling, both of which can negatively impact cooking performance and food quality.

Safety is also a top priority with the E4, as it incorporates features such as a built-in safety shut-off mechanism that activates if the temperature exceeds safe levels. Additionally, the fryer's robust construction minimizes the risks of spills and accidents in the kitchen, making it a reliable choice for high-traffic environments.

The Frymaster E4 also emphasizes energy efficiency, designed to meet stringent energy-saving standards without compromising performance. This is crucial in the current market, where energy costs can significantly impact overall profitability.

In conclusion, the Frymaster E4 offers an impressive combination of innovative technology, safety, and efficiency. Its programmable controls, high-performance frying capabilities, and advanced filtration and oil management systems make it an essential tool for any commercial kitchen aiming to enhance productivity and food quality. As the demands of the food industry continue to grow, the E4 stands out as a reliable partner for chefs looking to elevate their frying operations.
Top Page Image Contents