Frymaster E4 manual Disconnect flexlines indicated by the arrows

Page 41

A pump seized by debris or hard shortening can usually be freed by manually moving the gears with a screwdriver or other instrument.

Disconnect power to the filter system, remove the input plumbing from the pump, and use a screwdriver to manually turn the gears.

Turning the pump gears in reverse will release a hard particle.

Turning the pump gears forward will push softer objects and solid shortening through the pump and allow free movement of the gears.

Incorrectly sized or installed paper/pads will also allow food particles and sediment to pass through and clog the suction tube on the bottom of the filter pan. Particles large enough to block the suction tube may indicate that the crumb tray is not being used. Pan blockage can also occur if shortening is left in the pan and allowed to solidify. Blockage removal can be accomplished by forcing the item out with an auger or drain snake. Compressed air or other pressurized gases should not be used to force out the blockage.

7.9.2 Replacing the Filter Motor, Filter Pump and Related Components

1.Remove the filter pan and lid from the unit. Drain the frypots into a Shortening Disposal Unit (SDU) or other appropriate metal container.

DANGER

DO NOT drain more than one full frypot or two split frypots into the SDU at one time.

2.Disconnect the fryer from the electrical power supply and reposition it to gain access to both the front and rear.

3.Disconnect the two flexlines running to the oil-return manifold at the rear of the fryer as well as the pump suction flexline at the end of the filter pan connection (see photo below).

Disconnect flexlines indicated by the arrows.

7-10

Image 41
Contents Manual Hour Service HotlinePage Canada RE Series Marine Electric Fryers Operator Troubleshooting Iii General Safety InformationController Information Shipping Damage Claim ProcedureService Information Introduction Power Requirements Page Single Fryer with filter Dimensions and WeightsRE Series Marine E4 Electric Fryers Operating Instructions Equipment Setup and Shutdown ProceduresDescription Introduction Controller Operating Instructions Do not cancel the melt-cycle mode if using solid shorteningDisabling or Enabling the MELT-CYCLE Cancel Switch RE Series Marine E4 Electric Fryers Filtration Instructions Inspect O-Rings Screen Filter Paper Open valve by Rotating the handle 90º Page Draining and Disposing of Waste Oil RE Series Marine E4 Electric Fryers Preventive Maintenance Page Fryer Annual/Periodic System InspectionBuilt-In Filtration System RE Series Marine E4 Electric Fryers Operator Troubleshooting Troubleshooting Control and Heating Problems Problem Probable Causes Corrective ActionProblem Start Filtration ProblemsProblem Replacing Component Box Components Replacing a Remote Digital ControllerReplacing a High-Limit Thermostat Replacing a Temperature Probe Replacing a Heating Element Page Replacing Contactor Box Components Replacing a Frypot Reinstall the drain tube assembly Page Disconnect flexlines indicated by the arrows Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartWiring Diagram, Simplified RE17 Wiring Diagram, System Wiring Diagram, Contactor Box Wiring Wiring Diagram, Wiring Harness Wiring Diagram, Remote Cable Accessories RE Series Marine E4 Electric Fryers Parts ListPage Back Panel, Upper Single FPRE117 Page 106-6452 FPRE217 Double Station Fryer Cabinet Assembly, Fpre Electric Double S/S Drain Tube, Left/Right End Short Valve Assembly, Full Vat Drain FPRE217 Drain Valve Assembly and Component Parts Relays are not replaceable Electronics and Wiring Components 8.4.1 Component BoxesContactor Boxes Component BoxesContactor Boxes Terminal Blocks Heating Element Assembly and Associated Parts Heating Element Assembly and Associated Parts For other controllers, cables and harnesses see manual Component Box and Filter Pump Wiring Harnesses Page Assembly, Filter Pan Single FPRE117 includes pan and lid FPRE217 Filtration Components Suction Tube Oil Return System Components Frypot Assembly and ThermostatOil Return System Components Oil Disposal Plumbing Wiring Connectors, Pin Terminals, Seals, and Power Cords Component Fasteners Service Hotline
Related manuals
Manual 86 pages 38.42 Kb Manual 2 pages 51.67 Kb Manual 36 pages 37.47 Kb

E4 specifications

The Frymaster E4 is an advanced fryer that represents the cutting edge of commercial frying technology. Designed for efficiency and performance, it is favored by restaurants and fast-food chains looking to optimize their cooking processes while maintaining exceptional food quality.

One of the standout features of the Frymaster E4 is its programmable controls. With an intuitive digital interface, operators can easily adjust cooking temperatures, times, and even recipes with just a few taps. This level of precision ensures that food is consistently cooked to perfection every time, reducing waste and improving overall efficiency in the kitchen.

The E4 is equipped with high-performance burners that ensure rapid heating and recovery times. This means that cooking oil reaches the desired temperatures quickly, allowing for faster frying cycles. Thus, busy kitchens can meet high-demand periods without compromising quality or service speed. The fryer also features a high-efficiency oil filtration system that automatically removes contaminants and prolongs the life of the frying oil, resulting in a significant reduction in operating costs over time.

Another notable technology in the Frymaster E4 is its oil level management system, which actively monitors oil levels and alerts the operator when replenishment is necessary. This feature prevents overfilling or underfilling, both of which can negatively impact cooking performance and food quality.

Safety is also a top priority with the E4, as it incorporates features such as a built-in safety shut-off mechanism that activates if the temperature exceeds safe levels. Additionally, the fryer's robust construction minimizes the risks of spills and accidents in the kitchen, making it a reliable choice for high-traffic environments.

The Frymaster E4 also emphasizes energy efficiency, designed to meet stringent energy-saving standards without compromising performance. This is crucial in the current market, where energy costs can significantly impact overall profitability.

In conclusion, the Frymaster E4 offers an impressive combination of innovative technology, safety, and efficiency. Its programmable controls, high-performance frying capabilities, and advanced filtration and oil management systems make it an essential tool for any commercial kitchen aiming to enhance productivity and food quality. As the demands of the food industry continue to grow, the E4 stands out as a reliable partner for chefs looking to elevate their frying operations.