Frymaster 8195991 operation manual Lighting the Fryer, For CE Fryers

Page 21

Lighting the Fryer

1. Press the computer/controller ON/OFF switch to the OFF position.

For CE Fryers

For Non-CE Fryers

Placing the ON/OFF switch in the OFF position also turns off the gas valve. Wait five minutes before continuing with Step 2, which will also turn on the gas valve.

After placing the ON/OFF switch in the OFF position, turn the gas valve knob to the OFF position. Wait 5 minutes, then turn the knob to the ON postion and proceed with Step 2.

Honeywell

ON

OFF

Honeywell

ON

OFF

2.Press the computer/controller ON/OFF switch to the ON position and set the thermostat or program the computer for normal cooking temperature.

3.If the burners fail to light, press the ON/OFF switch to the OFF position and wait 60 seconds. Repeat step 2.

4.The fryer will automatically enter the melt cycle mode if the frypot temperature is below 180ºF (82ºC). (NOTE: During the melt cycle, the burners will repeatedly fire for a few seconds, then go out for a longer period.) When the frypot temperature reaches 180ºF (82ºC), the unit will automatically switch to the heating mode. The burners will remain lit until the frypot temperature reaches the programmed cooking temperature.

5.After the burners have been lit for at least 90 seconds, observe the flames through the burner viewing ports located on each side of the combustion air blower.

Left Viewing Ports are

Right Viewing Ports

behind the motor

 

housings.

 

The optimum burn is a bright orange-red glow. If a blue flame is observed, or if there are dark spots on a burner face, adjust the air gas mixture as follows: On the side of the blower housing opposite

3-2

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 8195991 Hour Service HotlineCanada Iii PRO H55 Series GAS Fryer Table of Contents This page Intentionally Left Blank Parts Ordering and Service Information PRO H55 Series GAS Fryer General InformationApplicability and Validity European Community CE Specific Information Safety InformationInstallation, Operating, and Service Personnel Equipment DescriptionDefinitions What to do if your equipment arrives damaged Shipping Damage Claim ProcedureGeneral Installation Requirements PRO H55 Series GAS Fryer Installation InstructionsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE StandardPressure mbar CE Gas Conversion Kits for Units with Gas Valve Non-CE Gas Conversion KitsCE GAS Conversion Instructions This page Intentionally Left Blank Controller Operation and Programming PRO H55 Series GAS Fryer Operating InstructionsFor CE Fryers Lighting the FryerShutting the Fryer Down Boiling Out the FrypotThis page Intentionally Left Blank PRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Use filter powder with the pad Preparation for Use with the Magnasol Filter AssemblyPage Snap the optional Power Shower into position Filter Pump Reset Switch Reassembly CleaningDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal Fryer Preventive Maintenance Checks and Service PRO H55 Series GAS Fryers Preventive MaintenanceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutClean Filter Pan, Detachable Parts and Accessories Check Computer Magic III.5 Set Point Accuracy Authorized Service Center for assistanceClean Combustion Air Blower Assembly Quarterly Checks and ServiceLeft Viewing Port is Behind Motor Right Check Burner Manifold Pressure Clean Gas Valve Vent TubeFryer Built-In Filtration System Introduction PRO H55 Series GAS Fryers Operator TroubleshootingIndicator is on, but With alarmNo display on Computer orRecovery is slow Heating indicatorWhen cooking Fryer is operating Sound when burnersTroubleshooting Fryers with Solid State Analog Controller Heating mode light Is on and blower is Fryer is slow coming Out of melt cycle Heating mode lightWill not ignite Heating mode light Normally. BlowerPump won’t start Troubleshooting the Built-in Filtration SystemPump stops during FilteringPump starts, but no Power Shower is notTransfer takes place Or the transfer isBasket lift Troubleshooting the Basket LiftMovement is jerky And/or noisyService Hotline

8195991 specifications

The Frymaster 8195991 is a premium deep-fryer, designed specifically for commercial kitchens that require high performance and efficiency. This model is known for its robust construction and state-of-the-art technology, making it a favored choice among restaurateurs and chefs alike.

One of the most prominent features of the Frymaster 8195991 is its advanced fry control system. This technology ensures consistent frying results by automatically adjusting temperatures according to the type of food being fried. It helps maintain oil quality and enhances food flavor, crucial factors in any food establishment. Additionally, the fryer includes a built-in filtration system that prolongs oil life and reduces operational costs, ensuring that kitchens can maintain quality while saving money on oil purchases.

The Frymaster 8195991 boasts a digital display that simplifies the cooking process. With user-friendly controls, chefs can easily set cooking times and temperatures while monitoring frying progress in real-time. This feature is particularly useful during peak service hours, enabling kitchens to operate efficiently without sacrificing food quality. Safety is also a priority, and the fryer comes equipped with numerous safety features, including an automatic shut-off mechanism and temperature alarms to prevent overheating.

Another key characteristic of the Frymaster 8195991 is its sleek and compact design, which allows it to fit seamlessly into various kitchen layouts. Despite its smaller footprint, this fryer provides ample frying capacity, accommodating various food items such as French fries, chicken, and other fried delicacies. Its stainless steel construction ensures durability, while the easy-to-clean surfaces reduce maintenance time.

Moreover, the Frymaster 8195991 is designed with energy efficiency in mind. It utilizes innovative heating elements that minimize energy consumption without compromising on performance. This makes it an environmentally friendly choice for businesses looking to reduce their carbon footprint.

In conclusion, the Frymaster 8195991 is an exceptional deep-fryer tailored for commercial use, combining advanced technology and thoughtful engineering. With its digital controls, built-in filtration system, safety features, and energy efficiency, it stands out as a reliable and effective tool for any busy kitchen environment. Whether frying up appetizers or main dishes, the Frymaster 8195991 delivers consistent results, ensuring that culinary creations are not only delicious but also prepared with the utmost care and efficiency.
Top Page Image Contents