Frymaster 8195991 Pump starts, but no, Transfer takes place, Or the transfer is, Very slow

Page 48

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

 

C. Pump blockage.

C. Pump blockages are usually

 

Test: Close the drain valve. Place

caused by sediment build-up in

 

the pump due to improperly sized

 

the filter handle in the OFF

or installed filter paper and failure

(Continued from

position, allow the pump to cool

to use the crumb screen. Call

for at least 45 minutes, and then

FASC to have blockage cleared.

previous page.)

press the reset button on the pump

 

 

Ensure that filter paper is of the

 

motor. Pull the filter pan from the

 

unit and then activate the pump.

proper size and is installed

 

If the pump motor hums and then

properly, and that the crumb

 

stops, the pump is blocked.

screen is used.

 

 

A. To properly filter, the oil should

 

 

be at or near 350°F (177°C). At

 

 

temperatures lower than this, the

 

A. Cooking oil is too cold for

oil becomes too thick to pass

 

filtering.

through the filter medium easily,

 

 

resulting in much slower oil

 

 

return and eventual overheating of

 

 

the filter pump motor.

 

B. Improperly installed or prepared

 

Pump starts, but no

filter pan components.

B. Remove the oil from the filter pan

 

transfer takes place

Test: Close the drain valve.

and replace the filter paper,

or the transfer is

Move the filter handle to the OFF

ensuring that the filter screen is in

very slow.

position, pull the filter pan (and

place under the paper.

 

 

Power Shower, if so equipped)

C. If this does not correct the

 

from the unit. Move the filter

 

handle to the ON position.

problem, the filter suction tube is

 

 

probably blocked. Remove the

 

If a strong stream of air is being

blockage using a thin, flexible

 

pumped out of the oil return port

wire. If unable to remove the

 

(or the Power Shower port), the

blockage, call FASC.

 

problem is with the filter pan

 

 

components.

 

 

A. Plugged openings or solidified

 

 

shortening in the Power Shower.

 

 

Test: Look for oil squirting out

A. Clean the Power Shower per

Power Shower is not

instructions in Chapter 5 of this

around the Power Shower gasket

manual.

spraying properly.

but not coming out of the holes

 

 

around the frame. If so, Power

 

 

Shower is obstructed.

 

 

B. Missing/worn o-rings and gasket

B. Verify that o-rings and gasket are

 

on Power Shower.

present and in good condition.

6-7

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Hour Service Hotline 8195991Canada Iii PRO H55 Series GAS Fryer Table of Contents This page Intentionally Left Blank Parts Ordering and Service Information PRO H55 Series GAS Fryer General InformationApplicability and Validity Safety Information European Community CE Specific InformationInstallation, Operating, and Service Personnel Equipment DescriptionDefinitions Shipping Damage Claim Procedure What to do if your equipment arrives damagedPRO H55 Series GAS Fryer Installation Instructions General Installation RequirementsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures CE Standard Gas Connection Pipe SizesPressure mbar Non-CE Gas Conversion Kits CE Gas Conversion Kits for Units with Gas ValveCE GAS Conversion Instructions This page Intentionally Left Blank PRO H55 Series GAS Fryer Operating Instructions Controller Operation and ProgrammingLighting the Fryer For CE FryersBoiling Out the Frypot Shutting the Fryer DownThis page Intentionally Left Blank PRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Use filter powder with the padPage Snap the optional Power Shower into position Filter Pump Reset Switch Cleaning ReassemblyDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal PRO H55 Series GAS Fryers Preventive Maintenance Fryer Preventive Maintenance Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutClean Filter Pan, Detachable Parts and Accessories Authorized Service Center for assistance Check Computer Magic III.5 Set Point AccuracyQuarterly Checks and Service Clean Combustion Air Blower AssemblyLeft Viewing Port is Behind Motor Right Clean Gas Valve Vent Tube Check Burner Manifold PressureFryer Built-In Filtration System PRO H55 Series GAS Fryers Operator Troubleshooting IntroductionWith alarm Indicator is on, butNo display on Computer orHeating indicator Recovery is slowWhen cooking Fryer is operating Sound when burnersTroubleshooting Fryers with Solid State Analog Controller Fryer is slow coming Out of melt cycle Heating mode light Heating mode light Is on and blower isWill not ignite Heating mode light Normally. BlowerTroubleshooting the Built-in Filtration System Pump won’t startPump stops during FilteringPower Shower is not Pump starts, but noTransfer takes place Or the transfer isTroubleshooting the Basket Lift Basket liftMovement is jerky And/or noisyService Hotline

8195991 specifications

The Frymaster 8195991 is a premium deep-fryer, designed specifically for commercial kitchens that require high performance and efficiency. This model is known for its robust construction and state-of-the-art technology, making it a favored choice among restaurateurs and chefs alike.

One of the most prominent features of the Frymaster 8195991 is its advanced fry control system. This technology ensures consistent frying results by automatically adjusting temperatures according to the type of food being fried. It helps maintain oil quality and enhances food flavor, crucial factors in any food establishment. Additionally, the fryer includes a built-in filtration system that prolongs oil life and reduces operational costs, ensuring that kitchens can maintain quality while saving money on oil purchases.

The Frymaster 8195991 boasts a digital display that simplifies the cooking process. With user-friendly controls, chefs can easily set cooking times and temperatures while monitoring frying progress in real-time. This feature is particularly useful during peak service hours, enabling kitchens to operate efficiently without sacrificing food quality. Safety is also a priority, and the fryer comes equipped with numerous safety features, including an automatic shut-off mechanism and temperature alarms to prevent overheating.

Another key characteristic of the Frymaster 8195991 is its sleek and compact design, which allows it to fit seamlessly into various kitchen layouts. Despite its smaller footprint, this fryer provides ample frying capacity, accommodating various food items such as French fries, chicken, and other fried delicacies. Its stainless steel construction ensures durability, while the easy-to-clean surfaces reduce maintenance time.

Moreover, the Frymaster 8195991 is designed with energy efficiency in mind. It utilizes innovative heating elements that minimize energy consumption without compromising on performance. This makes it an environmentally friendly choice for businesses looking to reduce their carbon footprint.

In conclusion, the Frymaster 8195991 is an exceptional deep-fryer tailored for commercial use, combining advanced technology and thoughtful engineering. With its digital controls, built-in filtration system, safety features, and energy efficiency, it stands out as a reliable and effective tool for any busy kitchen environment. Whether frying up appetizers or main dishes, the Frymaster 8195991 delivers consistent results, ensuring that culinary creations are not only delicious but also prepared with the utmost care and efficiency.
Top Page Image Contents