Frymaster 8195991 operation manual Fryer

Page 40

O-RING

GASKET

 

CLEAN-OUT PLUGS

If the system is equipped with a Power Shower, drain the Power Shower completely after each use. If oil is leaking at the point where the Power Shower plugs into the frypot, verify that the O-ring and gasket on the connection fitting are present and in good condition. If you suspect blockage, unscrew the clean-out plugs at each corner of the frame. Place the frame in a pan of hot water for several minutes to melt any accumulation of solidified oil/shortening. Use a long, narrow bottlebrush with hot water and detergent to clean inside the tubes. If necessary, insert a straightened paper clip or similarly sized wire into the holes in the frame to remove any solidified shortening or other blockages. Rinse with hot water, dry thoroughly, and reinstall the plugs before using.

DANGER

Failure to reinstall the clean-out plugs in the Power Shower will cause hot oil to spray out of the frypot during the filtering process, creating an extreme burn hazard to personnel.

5.3Annual/Periodic System Inspection

This appliance should be inspected and adjusted periodically by qualified service personnel as part of a regular kitchen maintenance program.

Frymaster recommends that a Factory Authorized Service Technician inspect this appliance at least annually as follows:

Fryer

Inspect the cabinet inside and out, front and rear for excessive oil.

Verify that the flue opening is not obstructed by debris or accumulations of solidified oil or shortening.

Verify that burners and associated components (i.e. gas valves, pilot assemblies, ignitors, etc.) are in good condition and functioning properly. Inspect all gas connections for leaks and verify that all connections are properly tightened.

Verify that the burner manifold pressure is in accordance with that specified on the appliance’s rating plate.

5-7

Image 40
Contents Hour Service Hotline 8195991Canada Iii PRO H55 Series GAS Fryer Table of Contents This page Intentionally Left Blank PRO H55 Series GAS Fryer General Information Parts Ordering and Service InformationApplicability and Validity Safety Information European Community CE Specific InformationEquipment Description Installation, Operating, and Service PersonnelDefinitions Shipping Damage Claim Procedure What to do if your equipment arrives damagedPRO H55 Series GAS Fryer Installation Instructions General Installation RequirementsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures CE Standard Gas Connection Pipe SizesPressure mbar Non-CE Gas Conversion Kits CE Gas Conversion Kits for Units with Gas ValveCE GAS Conversion Instructions This page Intentionally Left Blank PRO H55 Series GAS Fryer Operating Instructions Controller Operation and ProgrammingLighting the Fryer For CE FryersBoiling Out the Frypot Shutting the Fryer DownThis page Intentionally Left Blank PRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Use filter powder with the padPage Snap the optional Power Shower into position Filter Pump Reset Switch Cleaning ReassemblyDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal PRO H55 Series GAS Fryers Preventive Maintenance Fryer Preventive Maintenance Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutClean Filter Pan, Detachable Parts and Accessories Authorized Service Center for assistance Check Computer Magic III.5 Set Point AccuracyQuarterly Checks and Service Clean Combustion Air Blower AssemblyLeft Viewing Port is Behind Motor Right Clean Gas Valve Vent Tube Check Burner Manifold PressureFryer Built-In Filtration System PRO H55 Series GAS Fryers Operator Troubleshooting IntroductionWith alarm Indicator is on, butNo display on Computer orHeating indicator Recovery is slowWhen cooking Fryer is operating Sound when burnersTroubleshooting Fryers with Solid State Analog Controller Fryer is slow coming Out of melt cycle Heating mode light Heating mode light Is on and blower isWill not ignite Heating mode light Normally. BlowerTroubleshooting the Built-in Filtration System Pump won’t startPump stops during FilteringPower Shower is not Pump starts, but noTransfer takes place Or the transfer isTroubleshooting the Basket Lift Basket liftMovement is jerky And/or noisyService Hotline

8195991 specifications

The Frymaster 8195991 is a premium deep-fryer, designed specifically for commercial kitchens that require high performance and efficiency. This model is known for its robust construction and state-of-the-art technology, making it a favored choice among restaurateurs and chefs alike.

One of the most prominent features of the Frymaster 8195991 is its advanced fry control system. This technology ensures consistent frying results by automatically adjusting temperatures according to the type of food being fried. It helps maintain oil quality and enhances food flavor, crucial factors in any food establishment. Additionally, the fryer includes a built-in filtration system that prolongs oil life and reduces operational costs, ensuring that kitchens can maintain quality while saving money on oil purchases.

The Frymaster 8195991 boasts a digital display that simplifies the cooking process. With user-friendly controls, chefs can easily set cooking times and temperatures while monitoring frying progress in real-time. This feature is particularly useful during peak service hours, enabling kitchens to operate efficiently without sacrificing food quality. Safety is also a priority, and the fryer comes equipped with numerous safety features, including an automatic shut-off mechanism and temperature alarms to prevent overheating.

Another key characteristic of the Frymaster 8195991 is its sleek and compact design, which allows it to fit seamlessly into various kitchen layouts. Despite its smaller footprint, this fryer provides ample frying capacity, accommodating various food items such as French fries, chicken, and other fried delicacies. Its stainless steel construction ensures durability, while the easy-to-clean surfaces reduce maintenance time.

Moreover, the Frymaster 8195991 is designed with energy efficiency in mind. It utilizes innovative heating elements that minimize energy consumption without compromising on performance. This makes it an environmentally friendly choice for businesses looking to reduce their carbon footprint.

In conclusion, the Frymaster 8195991 is an exceptional deep-fryer tailored for commercial use, combining advanced technology and thoughtful engineering. With its digital controls, built-in filtration system, safety features, and energy efficiency, it stands out as a reliable and effective tool for any busy kitchen environment. Whether frying up appetizers or main dishes, the Frymaster 8195991 delivers consistent results, ensuring that culinary creations are not only delicious but also prepared with the utmost care and efficiency.