Frymaster 8195991 Troubleshooting the Built-in Filtration System, Pump won’t start, Filtering

Page 47

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Heating mode light

 

 

is ON with power

 

 

switch in OFF

 

If available, substitute a controller

position. After

 

known to be working for the

initial startup, fryer

Failed controller.

suspect controller. If the fryer

continues to heat

 

functions correctly, order

until trouble light

 

replacement from FASC.

comes on. Frypot

 

 

temperature is

 

 

above 410F (210°C).

 

 

6.4Troubleshooting the Built-in Filtration System

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

 

A. Thermal overload switch has

A. If the pump runs normally after

 

resetting the thermal overload

 

tripped on an overheated motor.

switch, the pump was overheated.

 

Test: If the pump stopped

Always filter with the cooking oil

 

suddenly during the filtering

at or near frying temperature.

 

process, especially if after several

 

 

filtering cycles, the pump motor

Allow the pump motor to cool off

 

has probably overheated. Place

for about ten minutes after

 

the filter handle in the OFF

filtering two full frypots one after

 

position, allow the pump to cool

the other.

 

for at least 45 minutes, and then

 

Pump won’t start.

press the reset button on the pump

Check the filter paper between

motor. Attempt to activate the

filterings. Replace the paper if

 

OR

pump.

there is a large accumulation of

 

sediment.

 

 

Pump stops during

B. Failed filter handle microswitch.

 

filtering.

Test: If this is a multi-pot fryer,

 

 

 

 

attempt to operate the pump using

B. If the switch is loose, tighten the

 

a different handle. If the pump

nuts and bolts holding it in place,

 

starts, the handle microswitch is

 

ensuring that when the handle is

 

either out of alignment or has

 

placed in the ON position, the

 

failed.

 

lever on the microswitch is

 

 

 

When the handle is placed in the

pressed firmly against the switch.

 

 

 

ON position, the lever on the

If the switch has failed, call

 

microswitch should be firmly

 

FASC.

 

pressed against the switch. If so,

 

 

 

the switch has failed. If not, the

 

 

switch is loose and/or misaligned.

 

 

 

 

6-6

Page 46 Page 48
Image 47
Page 46 Page 48
Contents 8195991 Hour Service HotlineCanada Iii PRO H55 Series GAS Fryer Table of Contents This page Intentionally Left Blank Applicability and Validity Parts Ordering and Service InformationPRO H55 Series GAS Fryer General Information European Community CE Specific Information Safety InformationDefinitions Installation, Operating, and Service PersonnelEquipment Description What to do if your equipment arrives damaged Shipping Damage Claim ProcedureGeneral Installation Requirements PRO H55 Series GAS Fryer Installation InstructionsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE StandardPressure mbar CE Gas Conversion Kits for Units with Gas Valve Non-CE Gas Conversion KitsCE GAS Conversion Instructions This page Intentionally Left Blank Controller Operation and Programming PRO H55 Series GAS Fryer Operating InstructionsFor CE Fryers Lighting the FryerShutting the Fryer Down Boiling Out the FrypotThis page Intentionally Left Blank PRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Use filter powder with the pad Preparation for Use with the Magnasol Filter AssemblyPage Snap the optional Power Shower into position Filter Pump Reset Switch Reassembly CleaningDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal Clean Fryer Cabinet Inside and Out PRO H55 Series GAS Fryers Preventive MaintenanceFryer Preventive Maintenance Checks and Service Inspect Fryer and Accessories for DamageClean Filter Pan, Detachable Parts and Accessories Check Computer Magic III.5 Set Point Accuracy Authorized Service Center for assistanceClean Combustion Air Blower Assembly Quarterly Checks and ServiceLeft Viewing Port is Behind Motor Right Check Burner Manifold Pressure Clean Gas Valve Vent TubeFryer Built-In Filtration System Introduction PRO H55 Series GAS Fryers Operator TroubleshootingComputer or With alarmIndicator is on, but No display onSound when burners Heating indicatorRecovery is slow When cooking Fryer is operatingTroubleshooting Fryers with Solid State Analog Controller Normally. Blower Fryer is slow coming Out of melt cycle Heating mode lightHeating mode light Is on and blower is Will not ignite Heating mode lightFiltering Troubleshooting the Built-in Filtration SystemPump won’t start Pump stops duringOr the transfer is Power Shower is notPump starts, but no Transfer takes placeAnd/or noisy Troubleshooting the Basket LiftBasket lift Movement is jerkyService Hotline

8195991 specifications

The Frymaster 8195991 is a premium deep-fryer, designed specifically for commercial kitchens that require high performance and efficiency. This model is known for its robust construction and state-of-the-art technology, making it a favored choice among restaurateurs and chefs alike.

One of the most prominent features of the Frymaster 8195991 is its advanced fry control system. This technology ensures consistent frying results by automatically adjusting temperatures according to the type of food being fried. It helps maintain oil quality and enhances food flavor, crucial factors in any food establishment. Additionally, the fryer includes a built-in filtration system that prolongs oil life and reduces operational costs, ensuring that kitchens can maintain quality while saving money on oil purchases.

The Frymaster 8195991 boasts a digital display that simplifies the cooking process. With user-friendly controls, chefs can easily set cooking times and temperatures while monitoring frying progress in real-time. This feature is particularly useful during peak service hours, enabling kitchens to operate efficiently without sacrificing food quality. Safety is also a priority, and the fryer comes equipped with numerous safety features, including an automatic shut-off mechanism and temperature alarms to prevent overheating.

Another key characteristic of the Frymaster 8195991 is its sleek and compact design, which allows it to fit seamlessly into various kitchen layouts. Despite its smaller footprint, this fryer provides ample frying capacity, accommodating various food items such as French fries, chicken, and other fried delicacies. Its stainless steel construction ensures durability, while the easy-to-clean surfaces reduce maintenance time.

Moreover, the Frymaster 8195991 is designed with energy efficiency in mind. It utilizes innovative heating elements that minimize energy consumption without compromising on performance. This makes it an environmentally friendly choice for businesses looking to reduce their carbon footprint.

In conclusion, the Frymaster 8195991 is an exceptional deep-fryer tailored for commercial use, combining advanced technology and thoughtful engineering. With its digital controls, built-in filtration system, safety features, and energy efficiency, it stands out as a reliable and effective tool for any busy kitchen environment. Whether frying up appetizers or main dishes, the Frymaster 8195991 delivers consistent results, ensuring that culinary creations are not only delicious but also prepared with the utmost care and efficiency.
Top Page Image Contents