Maytag ACO1860AC Parts, Tools, and Materials, Following parts are supplied with the oven

Page 32

Installation Instruction

Parts, Tools, and Materials

The following parts are supplied with the oven:

NOTE: Depending on ventilation requirements, not all parts will be used.

Backdraft damper / duct connector

(for roof-venting or wall-venting installation) Not Actual Size ( 2 pieces must be assembled as shown )

One power cord clamp and

One dark-colored mounting screw

(to hold the power cord) Actual Size

Two self - tapping screws

(for attaching the damper duct connector)

One lock pin and one washer-

One power cord clamp bushing -

(for the cord hole in a metal upper cabinet)

Four 1/4" x 2" lag screws -

(for wall stud holes)

Two 1/4" x 2" bolts -

(for securing to the upper cabinet)

Four 1/4" x 3" toggle bolts -

(for drywall holes)

Four spring toggle heads -

(for the toggle bolts)

Two washers -

(for the two upper cabinet bolts)

NOTE: Install at least two lag screws into one 2” X 4” stud and four anchor bolts into the wall. The mounting area must meet the 150 lbs. weight requirement.

Tools and materials required for installation:

List of tools include: Stud finder or thin nail, Saber saw, Keyhole saw, Electric drill, Phillips and Flat blade screwdriver, Pencil, Tape measure (metal), Plumb line, Tin snips, Caulking gun, Duct tape, Clear tape, Wood and Metal drill bits.

NOTE: Use the carton or heavy material for covering the counter top.

NOTE: Ductwork required for installation is not included. All wall and roof caps must have a back-draft damper.

16021668 Rev. 0

A–4

©2002 Maytag Appliances Company

Image 32
Contents Service Customer Service Support Center Recognize Safety Symbols, Words, and LabelsImportant Information Web Site Telephone NumberTable of Contents Wiring Important Product InformationGrounding Instructions Servicing of Grounded ProductsImportant Safety Information Microwave Leakage Testing General Information Oven control Microwave Oven DescriptionVent grille Testing Procedures High Voltage Capacitor High Voltage DiodeHumidity Sensor RelayACO1520/ACO1530 models Pad Conn ACO1560/MMV5156 models Pad ConnACO1560/MMV5156 models ACO1840/MMV4184 models Pad ConnCircuit Board Oven ThermostatFuse Fan MotorTroubleshooting Procedures Adjust or Wire across Replace high Thermostat When Start pad is Check Power Supply Fuse Disassembly Procedures Door AssemblyDoor Disassembly GrilleControl Panel BoardControl Panel Removal Relay ACO1520*, ACO1530*, and MMV5156Power Transformer Outer CaseScrew Control Panel Circuit Board RelayStirrer Assembly some models Interlock Door Latch SwitchesAdjusting Interlocks DiodeACO1840*, ACO1860*, JMV8196 MMV4184*, and MMV5186 High Voltage Capacitor RemovalMagnetron Fan Assembly Power Transformer RemovalTransformer Fuse RemovalMagnetron Thermal Fuse Magnetron Thermal FuseFan Motor Humidity Sensor RemovalBase Thermostat Light SocketTurntable Motor Vent BlowerWiring Diagram and Schematic ACO1560* and MMV5156* Models ACO18*, JMV8196*, MMV4184, and MMV5186* Models Installation Instruction Appendix aAvoid Electrical Shock Electrical rating of this oven 120V AC 60HzDo not expose yourself to excessive microwave energy Do not USE the Microwave OvenFollowing parts are supplied with the oven Tools and materials required for installationParts, Tools, and Materials Preparing Electrical Connection Preparing Venting SystemRoof-Venting Roof VentingRoom Venting Standard Fittings Ductwork LengthRoof Venting Installation Wall Venting InstallationRoom Venting Installation Recirculating Preparing Venting BlowerPreparing Template Placement Preparing Wall and Upper CabinetInstalling Mounting Plate Drilling Holes in the Wall and Upper CabinetAttaching Oven to the Wall Damper This page intentionally left blank Appendix B Charcoal Filter Replacement Care and CleaningCleaning the Grease Filters Cooktop/Night Light Replacement Oven Light Replacement