Maytag ACO1840AC, ACO1560AB, ACO1530AB, ACO1840AB, ACO1560AC, ACO1560AS, ACO1860AC, ACO1560AW Damper

Page 39

Installation Instruction

6.Roof-vented installation: Align the damper/duct connector with the vent on top of the microwave oven. Damper should be on top of tab. Use two tapping screws (bright-colored) to attach damper/ duct connector to the microwave oven.

damper

NOTE: Damper/duct connector must be attached to microwave oven after microwave oven is installed.

7.Roof venting installation: Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See, Preparing Venting System section. Use caulking to seal the exterior roof opening around the exhaust cap.

8.Use the power supply cord clamp to bundle the power supply cord. Install the power supply cord clamp inside the cabinet.

duct

power supply cord clamp

9.Grasp filter screen with one hand holding the ring and the other hand holding the opposite end. Insert the end of the filter screen without ring into the opening and slide towards the side of the microwave oven. Insert ring end of filter screen into the opening and slide entire screen towards the center of the microwave until screen is securely in position. Repeat for other filter screen.

10. Plug in the power supply cord.

©2002 Maytag Appliances Company

A–11

16021668 Rev. 0

Image 39

Contents Service Web Site Telephone Number Customer Service Support CenterRecognize Safety Symbols, Words, and Labels Important InformationTable of Contents Servicing of Grounded Products WiringImportant Product Information Grounding InstructionsImportant Safety Information Microwave Leakage Testing General Information Microwave Oven Description Vent grilleOven control Testing Procedures Relay High Voltage CapacitorHigh Voltage Diode Humidity SensorACO1840/MMV4184 models Pad Conn ACO1520/ACO1530 models Pad ConnACO1560/MMV5156 models Pad Conn ACO1560/MMV5156 modelsFan Motor Circuit BoardOven Thermostat FuseTroubleshooting Procedures Adjust or Wire across Replace high Thermostat When Start pad is Check Power Supply Fuse Grille Disassembly ProceduresDoor Assembly Door DisassemblyRelay ACO1520*, ACO1530*, and MMV5156 Control PanelBoard Control Panel RemovalRelay Power TransformerOuter Case Screw Control Panel Circuit BoardInterlock Door Latch Switches Stirrer Assembly some modelsHigh Voltage Capacitor Removal Adjusting InterlocksDiode ACO1840*, ACO1860*, JMV8196 MMV4184*, and MMV5186Fuse Removal Magnetron Fan AssemblyPower Transformer Removal TransformerHumidity Sensor Removal Magnetron Thermal FuseMagnetron Thermal Fuse Fan MotorVent Blower Base ThermostatLight Socket Turntable MotorWiring Diagram and Schematic ACO1560* and MMV5156* Models ACO18*, JMV8196*, MMV4184, and MMV5186* Models Appendix a Installation InstructionElectrical rating of this oven 120V AC 60Hz Avoid Electrical ShockDo not USE the Microwave Oven Do not expose yourself to excessive microwave energyTools and materials required for installation Parts, Tools, and MaterialsFollowing parts are supplied with the oven Roof Venting Preparing Electrical ConnectionPreparing Venting System Roof-VentingStandard Fittings Ductwork Length Room VentingPreparing Venting Blower Roof Venting InstallationWall Venting Installation Room Venting Installation RecirculatingPreparing Wall and Upper Cabinet Preparing Template PlacementDrilling Holes in the Wall and Upper Cabinet Installing Mounting PlateAttaching Oven to the Wall Damper This page intentionally left blank Appendix B Care and Cleaning Cleaning the Grease FiltersCharcoal Filter Replacement Oven Light Replacement Cooktop/Night Light Replacement