Maytag ACO1520AC, ACO1840AC Preparing Wall and Upper Cabinet, Preparing Template Placement

Page 36

Installation Instruction

4.Place blower unit back into cabinet. Verify exhaust ports face towards the front of the unit.

5.Attach blower plate to cabinet. Secure blower unit with screws that were removed in step 1.

Preparing Wall and Upper Cabinet

!CAUTION

To avoid property damage cover countertop or cooktop by placing a piece of cardboard from the carton or a heavy piece of material. Do not use plastic.

•Remove shipping material and parts from inside the microwave oven.

•Cover countertop or cooktop with a thick protective covering, to protect it from damage and dirt.

A thick, protective

covering

NOTE: For easy access to wall and upper cabinet, remove range from wall to allow easier measuring and drilling.

Preparing Template Placement

1.Find and mark the vertical center line on the back wall, using a tape measure and plumb line.

2.Find and mark placement of one or two points indicating stud location on the wall.

•Measure and mark stud location within the area marked H on the wall template.

•If wall studs cannot be located, consult a local building contractor.

!WARNING

To avoid risk of property damage or personal injury, do not attempt to install microwave oven if wall studs cannot be located.

3.Align plumb line on wall with center line on the wall template.

•Verify minimum width is 30" and the distance from the top of wall template to the range or countertop is at least 30".

4.Secure wall template to the wall.

•If cabinets are not level, adjust the wall template to align with cabinet.

•Oven must hang level. If the front edge of the cabinet is lower than the back edge, adjust wall template to be level with the cabinet front.

Upper cabinet template

Wall template

5.Measure the bottom of the upper cabinet frame. Trim the edges A, B, and C on the upper cabinet template, so template will fit on the bottom of the upper cabinet. If upper cabinet has a recessed frame, trim the template to fit inside the recessed area. Align the centerline of the upper cabinet template with the centerline on the wall template. Secure upper cabinet template in place.

16021668 Rev. 0

A–8

©2002 Maytag Appliances Company

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Service Customer Service Support Center Recognize Safety Symbols, Words, and LabelsImportant Information Web Site Telephone NumberTable of Contents Wiring Important Product InformationGrounding Instructions Servicing of Grounded ProductsImportant Safety Information Microwave Leakage Testing General Information Microwave Oven Description Vent grilleOven control Testing Procedures High Voltage Capacitor High Voltage DiodeHumidity Sensor RelayACO1520/ACO1530 models Pad Conn ACO1560/MMV5156 models Pad ConnACO1560/MMV5156 models ACO1840/MMV4184 models Pad ConnCircuit Board Oven ThermostatFuse Fan MotorTroubleshooting Procedures Adjust or Wire across Replace high Thermostat When Start pad is Check Power Supply Fuse Disassembly Procedures Door AssemblyDoor Disassembly GrilleControl Panel BoardControl Panel Removal Relay ACO1520*, ACO1530*, and MMV5156Power Transformer Outer CaseScrew Control Panel Circuit Board RelayStirrer Assembly some models Interlock Door Latch SwitchesAdjusting Interlocks DiodeACO1840*, ACO1860*, JMV8196 MMV4184*, and MMV5186 High Voltage Capacitor RemovalMagnetron Fan Assembly Power Transformer RemovalTransformer Fuse RemovalMagnetron Thermal Fuse Magnetron Thermal FuseFan Motor Humidity Sensor RemovalBase Thermostat Light SocketTurntable Motor Vent BlowerWiring Diagram and Schematic ACO1560* and MMV5156* Models ACO18*, JMV8196*, MMV4184, and MMV5186* Models Installation Instruction Appendix aAvoid Electrical Shock Electrical rating of this oven 120V AC 60HzDo not expose yourself to excessive microwave energy Do not USE the Microwave OvenTools and materials required for installation Parts, Tools, and MaterialsFollowing parts are supplied with the oven Preparing Electrical Connection Preparing Venting SystemRoof-Venting Roof VentingRoom Venting Standard Fittings Ductwork LengthRoof Venting Installation Wall Venting InstallationRoom Venting Installation Recirculating Preparing Venting BlowerPreparing Template Placement Preparing Wall and Upper CabinetInstalling Mounting Plate Drilling Holes in the Wall and Upper CabinetAttaching Oven to the Wall Damper This page intentionally left blank Appendix B Care and Cleaning Cleaning the Grease FiltersCharcoal Filter Replacement Cooktop/Night Light Replacement Oven Light Replacement
Top Page Image Contents