Maytag ACO1520AW, ACO1840AC, ACO1560AB, ACO1530AB, ACO1840AB, ACO1560AC Attaching Oven to the Wall

Page 38

Installation Instruction

NOTE: Leave at least the wall thickness of space to allow spring toggle head to open once placed into the wall.

Spring

Toggle bolt Wall toggle head

Mounting plate

4.Locate wall stud holes and insert lag screws through mounting plate and into 3/16" holes, do not tighten .

Mounting pate

Lag screw

5.	Insert toggle bolts through wall surface and tighten.
	Tighten lag screws at this point also.
6.	Slide washer onto the lock pin and place inside the

Power cord

Power cord

hole

2.Rotate the microwave upward until oven is against the bottom of the upper cabinet or cabinet frame.

3.Drop the lock pin and washer assembly into hole N, and push the pin downward as far as it will go.

upper cabinet for further use.

Lock pin

Washer

Washer

Lock pin

Attaching Oven to the Wall

4.Insert 3" X 1/4" bolts and washers down into holes J and K. Tighten the bolts until the gap between the microwave and cabinet has closed.

!WARNING

This unit is an excessive weight hazard, which can cause personal injury or property damage. Two or more people are required to lift unit. To prevent injury or property damage, use proper lifting and carrying techniques when moving unit.

1.Carefully lift microwave oven and hang it on support tabs at the bottom of the mounting plate. Reaching through upper cabinet, thread power supply cord through cutout in the bottom of the upper cabinet.

5.Remove the lock pin and washer. If wall or roof venting installation is used, skip to step 8.

16021668 Rev. 0

A–10

©2002 Maytag Appliances Company

Image 38

Contents Service Important Information Customer Service Support CenterRecognize Safety Symbols, Words, and Labels Web Site Telephone NumberTable of Contents Grounding Instructions WiringImportant Product Information Servicing of Grounded ProductsImportant Safety Information Microwave Leakage Testing General Information Oven control Microwave Oven DescriptionVent grille Testing Procedures Humidity Sensor High Voltage CapacitorHigh Voltage Diode RelayACO1560/MMV5156 models ACO1520/ACO1530 models Pad ConnACO1560/MMV5156 models Pad Conn ACO1840/MMV4184 models Pad ConnFuse Circuit BoardOven Thermostat Fan MotorTroubleshooting Procedures Adjust or Wire across Replace high Thermostat When Start pad is Check Power Supply Fuse Door Disassembly Disassembly ProceduresDoor Assembly GrilleControl Panel Removal Control PanelBoard Relay ACO1520*, ACO1530*, and MMV5156Screw Control Panel Circuit Board Power TransformerOuter Case RelayStirrer Assembly some models Interlock Door Latch SwitchesACO1840*, ACO1860*, JMV8196 MMV4184*, and MMV5186 Adjusting InterlocksDiode High Voltage Capacitor RemovalTransformer Magnetron Fan AssemblyPower Transformer Removal Fuse RemovalFan Motor Magnetron Thermal FuseMagnetron Thermal Fuse Humidity Sensor RemovalTurntable Motor Base ThermostatLight Socket Vent BlowerWiring Diagram and Schematic ACO1560* and MMV5156* Models ACO18*, JMV8196*, MMV4184, and MMV5186* Models Installation Instruction Appendix aAvoid Electrical Shock Electrical rating of this oven 120V AC 60HzDo not expose yourself to excessive microwave energy Do not USE the Microwave OvenFollowing parts are supplied with the oven Tools and materials required for installationParts, Tools, and Materials Roof-Venting Preparing Electrical ConnectionPreparing Venting System Roof VentingRoom Venting Standard Fittings Ductwork LengthRoom Venting Installation Recirculating Roof Venting InstallationWall Venting Installation Preparing Venting BlowerPreparing Template Placement Preparing Wall and Upper CabinetInstalling Mounting Plate Drilling Holes in the Wall and Upper CabinetAttaching Oven to the Wall Damper This page intentionally left blank Appendix B Charcoal Filter Replacement Care and CleaningCleaning the Grease Filters Cooktop/Night Light Replacement Oven Light Replacement