Bunn ITCB-DV manual Service Number, Procedure to enter the service number, Enter Service #?

Page 55

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

SERVICE NUMBER

This function allows the operator to enter in the telephone number to call if service is needed. The service num- ber will be displayed anytime there is a fault message displayed. (See Troubleshooting on page 63)

Procedure to enter the service number:

1.Press and hold the right hidden button until the display reads SET LANGUAGE. Press the right hidden button until the display reads:

ENTER SERVICE #?

2.Press and release YES. The display will now read SCROL THRU #'S NEXT ->NEXT NUMBER, fol- lowed by 000-000-0000. Up to 16 charactors are available.

3.Press the SCROL button to scroll through the num- bers. When the desired number is shown, press and release NEXT to move to the next digit in the phone number.

4.Repeat Step 3 until the entire number is entered.

5.Press and release DONE. The display will now read

SERVICE TOOLS?

ENTER SERVICE #?

NO YES

BREW	BREW	BREW
A	B	C

SCROL THRU #'S NEXT->NEXTNUMBER

BREW	BREW	BREW
A	B	C

000-000-0000

SCROL DONE NEXT

BREW	BREW	BREW
A	B	C

SERVICE TOOLS?

NO YES

P3049

Page 55	36748 070706

Image 55

Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisBUNN-O-MATIC Commercial Product Warranty Dual Voltage Machine IntroductionVolt Machine User Notices 0 7IRE .$ #29710.0009 Ptional &IELD 7IRING0 7IRE .$ #29710.0010 A separate conductor For earth ground Dual Volt Toggle Switch Electrical HOOK-UPElectrical Requirements Conductor for earth groundPlumbing Hook UP Plumbing RequirementsTank Drain Operating Controls Repeat for Brew B and Brew C Make sure the ON/OFF switch is OFF LED will not be litInitial SET-UP Viewing Assigned Recipes & Asset NumberWith a Smart Funnel and G9-2T DBC or MHG Grinder TEA BrewingCoffee Brewing Without a Smart Funnel and G9-2T DBC GrinderMedium CleaningGlossary Glossary Programming Programming SwitchesProgramming Section Screen Programming the BrewerImportant Programming Notes Read Carefully Ready to Brew Water TempProgramming the Brewer Programming Functions Flow ChartProgramming Functions Level Brew Lockout Procedure for setting Brew LockoutProgramming the Brewer Programming Functions Level 2 Procedure for setting LanguageSET Language Units Procedure for setting the UnitsProcedure for reviewing the recipes Review Recipes Modify recipe, set up standard recipesModify Show and Next Assign Recipe Master Temp YES Using a Smart Funnel and a G9-2T DBC or MHG GrinderDONE? Coffee Name Show Quit Save Coffee Name Setup CompleteReady to Brew Water Temp Card Contains Recipe forCoffee Name Modify Show Next Review RECIPES? No YESStored in the brewer’s memory If the brewing information is not correct, or it isBrew OZ XX.X Done + Review Recipes No YESTEA Modify Show Next Recipe Name Modify Show NextBrew OZ Dilute Dely Done +Batches DONE? Water for that particular batch size SET Pulse Brew No YESTea recipe to be modified Read Dilute OZTEA Recipes SET Pulse Brew Setting Pulse Brew Easy Pulse BrewBrew Read Dilute DelyRead Select Method Press and release DONE. The display should read Press and release YES. The display should now read Dilute OZOFF Time 1ST on TimeSET Pulse Brew No YES Select Method Easy Next ManualRead 2 Batches DONE? Setting for the batch size just programmed. AfterOccurs for that batch size StepCoffee recipe to be modified NO-NAME Coffee Modify Show NextSCREEN, press and release the ON/OFF button Last on Time Pre-Infusion to 4 minutes Coffee Recipes SET Pulse BrewRepeat steps 10, 11 Size to display the settings for that batch. After aDirectly to step Read SET Pulse BrewPress and release DONE. The display should read TEA Modify Show Next Pulse Brew Coffee Recipes Drip TimeRepeat steps 8 through Master Temp Using -and +, adjust the brew and faucet tem- peratureUsing -and +, adjust the ready temperature Procedure to set ready temperature Range 2 to 20 F 1 10 CReady Degree Write Enable ADSProcedure to Enable/Disable Ads Procedure to Write an AdCard no Write From the NEW AD? screen, press and release CardEnabl Sanitation Procedure for enabling sanitation Range 0.0 to 72.0 hrsDone Enable EnergysavrProcedure to enable energy savings mode EnableFreshTimerXXX Refill Enable Fresh TimerTimer CoffeeRange 0 to RefillSpray OZ/M Procedure to adjust the sprayhead flow rate set- tingDilute OZ/M Procedure to adjust the dilution flow rate settingCalibrate Spray Quit Start Calibrate FLOW? No YESSpray Head CAL No YES Container READY? Quit YESContainer READY? Quit YES Calibrate FLOW? No YESSpray Head CAL No YES Dilution CAL? No YES Brew COUNTERS? No YES Brew a Xxxx Next Reset Brew B Xxxx Next Reset Brew C Xxxx Next ResetYES SET Recipe TempsTemps ToolsPress and release YES. The display will now read Procedure to enter the asset numberAsset Number Enter Asset #?Service TOOLS? Service NumberProcedure to enter the service number Enter Service #?Following components can be individually tested Brew Valve Service ToolsProcedure to test components and outputs Test SwitchesP2883 36748 Right Hidden To Exit Nothing Pressed Service TOOLS? No YESTest SWITCHES? No YES Test OUTPUTS? No YESQuency DoneDefaults Factory Defaults No YESWill Replace ALL Brew Settings Are YOU SURE? No YES Factory DefaultsTEA 3 Recipe Factory Default ValuesTEA 1 Recipe TEA 2 RecipeNO-NAME Coffee Recipe Factory Default ValuesHOT TEA Recipe Iced Coffee RecipeTroubleshooting Remedy TroubleshootingProblem Probable CauseControl Board Problem Probable Cause RemedyBrew switch Brew valveTank drain clamp Problem Probable CauseAutomatic refill will not operate No water LongAutomatic refill will not operate or Refill valve Check the wiring harnessTo it is secure Water flows into tank continuously Refill valveTing If the left three digit numberHeating Time TOO Long Working order Problem is foundTank heaters Connect a voltmeter acrossObstructions. Clear or replace TionStrainer Direction of flow arrow must be Move the strainer and check forLime buildup Temperature probe Control Board Funnel tip Head for lime buildup Brew volume adjustmentImproper water pressure 90 psi 138 and 620 kPaBrew cycle should be started For proper extractionProper extraction Water temperatureWeak beverage Type of paper filter Coffee or tealeavesSolenoids Remove and clean lime off tank heatersPlumbing lines Water supply Tank heaters Schematic Wiring Diagram ITCB-DV #%-!4#72. $!2!- I4#! I4# Schematic Wiring Diagram ITCB-C-DV