Bunn ITCB-DV manual Plumbing Requirements, Plumbing Hook UP, Tank Drain

Page 7

PLUMBING REQUIREMENTS

This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1⁄2" (12.7 mm) or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1⁄4" (6.35 mm) flare.

NOTE - Bunn-O-Matic recommends 1⁄4" (6.35 mm) copper tubing for installations of less than 25 feet (7.62 m) and 3⁄8" (9.5 mm) for more than 25 feet (7.62 m) from the 1⁄2" (12.7) water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanita- tion Manual of the Food and Drug Administration (FDA). For models installed outside the U.S.A., you must comply with the applicable Plumbing/Sanitation Code for your area.

PLUMBING HOOK UP

1.Flush the water line and securely attach it to the inlet fitting at the bottom rear of the brewer.

2.Turn on the water supply.

TANK DRAIN

1.Remove back access cover.

2.Close the white clamp on the drain hose.

3.Unfasten the hose clamp at the inlet valve. Remove the hose from the valve.

4.Place the end of the drain hose in a container that has a minimum capacity of 2.0 gallons (7.5 liters).

5.Release the white clamp to drain the water from the tank.

6.When tank is empty, leave the white clamp open, and install the hose back on the valve. Tighten the hose clamp at the end of the hose around the valve fitting.

7.Replace the back access cover.

Page

36748 101505

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisBUNN-O-MATIC Commercial Product Warranty Dual Voltage Machine IntroductionVolt Machine User Notices 0 7IRE .$  #29710.0009 Ptional &IELD 7IRING0 7IRE .$  #29710.0010 A separate conductor For earth ground Dual Volt Toggle Switch Electrical HOOK-UPElectrical Requirements Conductor for earth groundPlumbing Hook UP Plumbing RequirementsTank Drain Operating Controls Repeat for Brew B and Brew C Make sure the ON/OFF switch is OFF LED will not be litInitial SET-UP Viewing Assigned Recipes & Asset NumberWith a Smart Funnel and G9-2T DBC or MHG Grinder TEA BrewingCoffee Brewing Without a Smart Funnel and G9-2T DBC GrinderMedium CleaningGlossary Glossary Programming Programming SwitchesProgramming Section Screen Programming the BrewerImportant Programming Notes Read Carefully Ready to Brew Water TempProgramming the Brewer Programming Functions Flow ChartProgramming Functions Level Brew Lockout Procedure for setting Brew LockoutProgramming the Brewer Programming Functions Level 2 Procedure for setting LanguageSET Language Units Procedure for setting the UnitsProcedure for reviewing the recipes Review Recipes Modify recipe, set up standard recipesModify Show and Next Assign Recipe Master Temp YES Using a Smart Funnel and a G9-2T DBC or MHG GrinderDONE? Coffee Name Show Quit Save Coffee Name Setup CompleteReady to Brew Water Temp Card Contains Recipe forCoffee Name Modify Show Next Review RECIPES? No YESStored in the brewer’s memory If the brewing information is not correct, or it isBrew OZ XX.X Done + Review Recipes No YESTEA Modify Show Next Recipe Name Modify Show NextBrew OZ Dilute Dely Done +Batches DONE? Water for that particular batch size SET Pulse Brew No YESTea recipe to be modified Read Dilute OZTEA Recipes SET Pulse Brew Setting Pulse Brew Easy Pulse BrewBrew Read Dilute DelyRead Select Method Press and release DONE. The display should read Press and release YES. The display should now read Dilute OZOFF Time 1ST on TimeSET Pulse Brew No YES Select Method Easy Next ManualRead 2 Batches DONE? Setting for the batch size just programmed. AfterOccurs for that batch size StepCoffee recipe to be modified NO-NAME Coffee Modify Show NextSCREEN, press and release the ON/OFF button Last on Time Pre-Infusion to 4 minutes Coffee Recipes SET Pulse BrewRepeat steps 10, 11 Size to display the settings for that batch. After aDirectly to step Read SET Pulse BrewPress and release DONE. The display should read TEA Modify Show Next Pulse Brew Coffee Recipes Drip TimeRepeat steps 8 through Master Temp Using -and +, adjust the brew and faucet tem- peratureUsing -and +, adjust the ready temperature Procedure to set ready temperature Range 2 to 20 F 1 10 CReady Degree Write Enable ADSProcedure to Enable/Disable Ads Procedure to Write an AdCard no Write From the NEW AD? screen, press and release CardEnabl Sanitation Procedure for enabling sanitation Range 0.0 to 72.0 hrsDone Enable EnergysavrProcedure to enable energy savings mode EnableFreshTimerXXX Refill Enable Fresh TimerTimer CoffeeRange 0 to RefillSpray OZ/M Procedure to adjust the sprayhead flow rate set- tingDilute OZ/M Procedure to adjust the dilution flow rate settingCalibrate Spray Quit Start Calibrate FLOW? No YESSpray Head CAL No YES Container READY? Quit YESContainer READY? Quit YES Calibrate FLOW? No YESSpray Head CAL No YES Dilution CAL? No YESBrew COUNTERS? No YES Brew a Xxxx Next ResetBrew B Xxxx Next Reset Brew C Xxxx Next ResetYES SET Recipe TempsTemps ToolsPress and release YES. The display will now read Procedure to enter the asset numberAsset Number Enter Asset #?Service TOOLS? Service NumberProcedure to enter the service number Enter Service #?Following components can be individually tested Brew Valve Service ToolsProcedure to test components and outputs Test SwitchesP2883 36748 Right Hidden To Exit Nothing Pressed Service TOOLS? No YESTest SWITCHES? No YES Test OUTPUTS? No YESQuency DoneDefaults Factory Defaults No YESWill Replace ALL Brew Settings Are YOU SURE? No YES Factory DefaultsTEA 3 Recipe Factory Default ValuesTEA 1 Recipe TEA 2 RecipeNO-NAME Coffee Recipe Factory Default ValuesHOT TEA Recipe Iced Coffee RecipeTroubleshooting Remedy TroubleshootingProblem Probable CauseControl Board Problem Probable Cause RemedyBrew switch Brew valveTank drain clamp Problem Probable CauseAutomatic refill will not operate No water LongAutomatic refill will not operate or Refill valve Check the wiring harnessTo it is secure Water flows into tank continuously Refill valveTing If the left three digit numberHeating Time TOO Long Working order Problem is foundTank heaters Connect a voltmeter acrossObstructions. Clear or replace TionStrainer Direction of flow arrow must be Move the strainer and check forLime buildup Temperature probe Control Board Funnel tip Head for lime buildup Brew volume adjustmentImproper water pressure 90 psi 138 and 620 kPaBrew cycle should be started For proper extractionProper extraction Water temperatureWeak beverage Type of paper filter Coffee or tealeavesSolenoids Remove and clean lime off tank heatersPlumbing lines Water supply Tank heaters Schematic Wiring Diagram ITCB-DV #%-!4#72. $!2!- I4#! I4# Schematic Wiring Diagram ITCB-C-DV

ITCB-DV specifications

The Bunn ITCB-DV is a commercial coffee brewer known for its efficiency, versatility, and excellent brewing capabilities. Designed for high-demand environments like restaurants, cafes, and other food service establishments, this machine stands out due to its innovative features and technologies that enhance user experience and brewing quality.

One of the main features of the Bunn ITCB-DV is its dual voltage system, allowing it to operate efficiently at both 120V and 240V. This adaptability makes it suitable for a variety of locations without compromising performance. The brewer is designed to brew up to 3.8 gallons of coffee per hour, making it perfect for busy settings where speed and volume are critical.

The ITCB-DV is equipped with a unique Smart Brew technology that ensures precise brewing temperatures and times. This feature guarantees optimal extraction of coffee flavors, resulting in a consistently delicious and aromatic brew. Additionally, the brewer incorporates a digital brew counter that helps users track daily coffee production, allowing for better inventory management.

With an adjustable brew basket and multiple batch sizes, the Bunn ITCB-DV caters to diverse brewing needs. Whether preparing single servings or larger quantities, the brewer accommodates various coffee preferences. The machine is also compatible with Bunn's airpot systems, ensuring that fresh coffee is easily accessible and can be served quickly to customers.

In terms of construction, the Bunn ITCB-DV is built to last. It features a stainless steel exterior that not only adds a sleek appearance but also ensures durability against the rigors of commercial use. Furthermore, the brewer has a front-loading design, which allows for easy access and maintenance, minimizing downtime.

The ITCB-DV is also energy-efficient, featuring a low-wattage option that reduces electricity consumption without sacrificing brewing quality. This characteristic not only helps in cutting down operational costs but also appeals to eco-conscious businesses aiming to reduce their environmental footprint.

Overall, the Bunn ITCB-DV is a reliable and feature-rich coffee brewing solution tailored for high-volume environments. Its combination of advanced technologies, user-friendly design, and robust construction makes it an excellent choice for businesses committed to delivering exceptional coffee experiences. With this brewer, operators can ensure that their customers always enjoy top-quality coffee, brewed with precision and care.
Top Page Image Contents