Bunn ITCB-DV manual Factory Defaults No YES, Will Replace ALL Brew Settings Are YOU SURE? No YES

Page 60

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

FACTORY DEFAULTS

This function allows the operator to erase ALL of the previously entered recipes and ad messages. Factory-set default values will replace ALL previous settings.

Procedure to set factory defaults:

1. Press and hold the right hidden button until the

display reads SET LANGUAGE. Press the right

hidden button until the display reads FACTORY

FACTORY DEFAULTS

NO YES

PRESSING NO WILL

BREW

BREW

BREW

RETURN TO

MAIN SCREEN

A

B

C

 

 

 

 

 

 

 

 

 

 

DEFAULTS.

2. Pressing NO will return to the MAIN SCREEN. Press

YES to restore defaults. The display will read WILL

REPLACE ALL BREW SETTINGS followed with ARE

YOU SURE?

3. Pressing NO in this confirmation screen will revert

to the MAIN SCREEN without resetting the brew-

ing setups to the defaults. Press YES to load the

defaults. After factory defaults have been restored,

the display will return to the MAIN SCREEN. The

factory default valves will have replaced ALL previ-

ously entered values. It will NOT reset the life brew

counter. If factory defaults are restored, it will be

necessary to recalibrate the flow rates. Refer to

pages 50-51.

PRESSING NO WILL

RETURN TO

MAIN SCREEN

WILL REPLACE ALL BREW SETTINGS

ARE YOU SURE?

NO YES

BREW

BREW

BREW

A

B

C

REPLACES ALL

PREVIOUS SETTINGS

P2886

Page 60

36748 101505

 

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Introduction Dual Voltage MachineVolt Machine User Notices Ptional &IELD 7IRING 0 7IRE .$  #29710.00090 7IRE .$  #29710.0010 Dual Volt Toggle Switch Electrical HOOK-UP Electrical RequirementsConductor for earth ground A separate conductor For earth groundPlumbing Requirements Plumbing Hook UPTank Drain Operating Controls Make sure the ON/OFF switch is OFF LED will not be lit Initial SET-UPViewing Assigned Recipes & Asset Number Repeat for Brew B and Brew CTEA Brewing Coffee BrewingWithout a Smart Funnel and G9-2T DBC Grinder With a Smart Funnel and G9-2T DBC or MHG GrinderCleaning MediumGlossary Glossary Programming Switches ProgrammingProgramming Section Programming the Brewer Important Programming Notes Read CarefullyReady to Brew Water Temp ScreenProgramming Functions Flow Chart Programming the BrewerProcedure for setting Brew Lockout Programming Functions Level Brew LockoutProcedure for setting Language Programming the Brewer Programming Functions Level 2SET Language Procedure for setting the Units UnitsReview Recipes Modify recipe, set up standard recipes Procedure for reviewing the recipesModify Show and Next Assign Recipe Using a Smart Funnel and a G9-2T DBC or MHG Grinder Master Temp YESDONE? Coffee Name Setup Complete Ready to Brew Water TempCard Contains Recipe for Coffee Name Show Quit SaveReview RECIPES? No YES Stored in the brewer’s memoryIf the brewing information is not correct, or it is Coffee Name Modify Show NextReview Recipes No YES TEA Modify Show NextRecipe Name Modify Show Next Brew OZ XX.X Done +Dilute Dely Done + Brew OZBatches DONE? SET Pulse Brew No YES Tea recipe to be modifiedRead Dilute OZ Water for that particular batch sizeSetting Pulse Brew Easy Pulse Brew TEA Recipes SET Pulse BrewRead Dilute Dely BrewRead Select Method Press and release YES. The display should now read Dilute OZ Press and release DONE. The display should read1ST on Time SET Pulse Brew No YESSelect Method Easy Next Manual OFF TimeSetting for the batch size just programmed. After Occurs for that batch sizeStep Read 2 Batches DONE?NO-NAME Coffee Modify Show Next Coffee recipe to be modifiedSCREEN, press and release the ON/OFF button Coffee Recipes SET Pulse Brew Last on Time Pre-Infusion to 4 minutesSize to display the settings for that batch. After a Directly to stepRead SET Pulse Brew Repeat steps 10, 11Press and release DONE. The display should read TEA Modify Show Next Coffee Recipes Drip Time Pulse BrewRepeat steps 8 through Using -and +, adjust the brew and faucet tem- perature Master TempProcedure to set ready temperature Range 2 to 20 F 1 10 C Using -and +, adjust the ready temperatureReady Degree Enable ADS Procedure to Enable/Disable AdsProcedure to Write an Ad WriteFrom the NEW AD? screen, press and release Card Card no WriteProcedure for enabling sanitation Range 0.0 to 72.0 hrs Enabl SanitationEnable Energysavr Procedure to enable energy savings modeEnableFreshTimer DoneEnable Fresh Timer TimerCoffee XXX RefillRefill Range 0 toProcedure to adjust the sprayhead flow rate set- ting Spray OZ/MProcedure to adjust the dilution flow rate setting Dilute OZ/MCalibrate FLOW? No YES Spray Head CAL No YESContainer READY? Quit YES Calibrate Spray Quit StartCalibrate FLOW? No YES Spray Head CAL No YESDilution CAL? No YES Container READY? Quit YESBrew a Xxxx Next Reset Brew B Xxxx Next ResetBrew C Xxxx Next Reset Brew COUNTERS? No YESSET Recipe Temps TempsTools YESProcedure to enter the asset number Asset NumberEnter Asset #? Press and release YES. The display will now readService Number Procedure to enter the service numberEnter Service #? Service TOOLS?Service Tools Procedure to test components and outputsTest Switches Following components can be individually tested Brew ValveP2883 36748 Service TOOLS? No YES Test SWITCHES? No YESTest OUTPUTS? No YES Right Hidden To Exit Nothing PressedDone QuencyFactory Defaults No YES Will Replace ALL Brew Settings Are YOU SURE? No YESFactory Defaults DefaultsFactory Default Values TEA 1 RecipeTEA 2 Recipe TEA 3 RecipeFactory Default Values HOT TEA RecipeIced Coffee Recipe NO-NAME Coffee RecipeTroubleshooting Troubleshooting ProblemProbable Cause RemedyProblem Probable Cause Remedy Brew switchBrew valve Control BoardProblem Probable Cause Automatic refill will not operate No waterLong Tank drain clampCheck the wiring harness Automatic refill will not operate or Refill valveWater flows into tank continuously Refill valve TingIf the left three digit number To it is secureHeating Time TOO Long Problem is found Tank heatersConnect a voltmeter across Working orderTion Strainer Direction of flow arrow must beMove the strainer and check for Obstructions. Clear or replaceLime buildup Temperature probe Control Board Funnel tip Brew volume adjustment Improper water pressure90 psi 138 and 620 kPa Head for lime buildupFor proper extraction Brew cycle should be startedWater temperature Weak beverage Type of paper filterCoffee or tealeaves Proper extractionRemove and clean lime off tank heaters SolenoidsPlumbing lines Water supply Tank heaters Schematic Wiring Diagram ITCB-DV #%-!4#72. $!2!- I4#! I4# Schematic Wiring Diagram ITCB-C-DV

ITCB-DV specifications

The Bunn ITCB-DV is a commercial coffee brewer known for its efficiency, versatility, and excellent brewing capabilities. Designed for high-demand environments like restaurants, cafes, and other food service establishments, this machine stands out due to its innovative features and technologies that enhance user experience and brewing quality.

One of the main features of the Bunn ITCB-DV is its dual voltage system, allowing it to operate efficiently at both 120V and 240V. This adaptability makes it suitable for a variety of locations without compromising performance. The brewer is designed to brew up to 3.8 gallons of coffee per hour, making it perfect for busy settings where speed and volume are critical.

The ITCB-DV is equipped with a unique Smart Brew technology that ensures precise brewing temperatures and times. This feature guarantees optimal extraction of coffee flavors, resulting in a consistently delicious and aromatic brew. Additionally, the brewer incorporates a digital brew counter that helps users track daily coffee production, allowing for better inventory management.

With an adjustable brew basket and multiple batch sizes, the Bunn ITCB-DV caters to diverse brewing needs. Whether preparing single servings or larger quantities, the brewer accommodates various coffee preferences. The machine is also compatible with Bunn's airpot systems, ensuring that fresh coffee is easily accessible and can be served quickly to customers.

In terms of construction, the Bunn ITCB-DV is built to last. It features a stainless steel exterior that not only adds a sleek appearance but also ensures durability against the rigors of commercial use. Furthermore, the brewer has a front-loading design, which allows for easy access and maintenance, minimizing downtime.

The ITCB-DV is also energy-efficient, featuring a low-wattage option that reduces electricity consumption without sacrificing brewing quality. This characteristic not only helps in cutting down operational costs but also appeals to eco-conscious businesses aiming to reduce their environmental footprint.

Overall, the Bunn ITCB-DV is a reliable and feature-rich coffee brewing solution tailored for high-volume environments. Its combination of advanced technologies, user-friendly design, and robust construction makes it an excellent choice for businesses committed to delivering exceptional coffee experiences. With this brewer, operators can ensure that their customers always enjoy top-quality coffee, brewed with precision and care.
Top Page Image Contents