Bunn 41343 manual SET NEW Recipes, Procedure to program the coffee name

Page 19

PROGRAMMING THE BREWER (cont.)

SET NEW RECIPES (cont.)

SET NEW RECIPE:

Using a RECIPE CARD to load coffee names and brew settings into the Single/Dual GPR-DBC with Smart Funnel:

The G9-2T DBC or MHG's memory contains certain coffee names. If the operator uses a coffee name that is not already stored in the grinder's memory, a RECIPE CARD can be obtained from the factory. The RECIPE CARD would include all the information needed to set up that particular coffee name. The information from the RECIPE CARD is loaded into the grinder's memory, then into the brewer's memory by holding the chip area up to the equipment's sensing coil. This informa- tion can include the coffee name, BREW VOLUMES, BYPASS PERCENTAGES, PULSE BREW TIMES, and DRIP-OUT TIMES for that particular coffee NAME. These can all be loaded in seconds.

Contact Bunn-O-Matic Corporation for the avail- ability of RECIPE CARDS.

NOTE: Instructions to program the brewer and grinder are printed on the RECIPE CARD, along with the coffee name that is being programmed.

Procedure to program the coffee name:

1.Remove the funnels (if present) from the funnel rails (both sides on DUAL brewers).

2.Position the RECIPE CARD vertically, so that the top end of the chip is beneath the funnel sensing coil (left side on DUAL brewers).

3.After a short pause the display will read CARD CON- TAINS RECIPE FOR then will change to (COFFEE NAME) SHOW QUIT SAVE. All brewing parameters for that coffee name are now transferred from the CARD to the brewer.

4.To show (view) this information, press and release SHOW. The display will scroll through all of the brew settings for all three batch sizes. The display will then return to CARD CONTAINS RECIPE FOR then will change to (COFFEE NAME) SHOW QUIT SAVE.

5.If all brew settings are correct, press SAVE. The display will read (COFFEE NAME) SETUP COM- PLETE. All brew settings for that name are now stored in the brewer's memory.

6.If the brewing information is not correct, or it is desired to exit the setup before the settings are loaded into the brewer's memory, press QUIT. The display will read (COFFEE NAME) NOT SAVED. The display will then return to the MAIN SCREEN.

READY TO BREW

WATER TEMP: 200°

POSITION CARD UNDER THE

SENSOR COIL

(left side on DUAL brewers)

CARD CONTAINS

RECIPE FOR

(COFFEE NAME)

SHOW QUIT SAVE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SCROLLS THROUGH ALL

 

 

(COFFEE NAME)

OF THE BREW SETTINGS

 

 

 

 

SETUP COMPLETE

FOR THE THREE BATCH

 

 

 

 

 

 

SIZES FOR THAT COFFEE

 

 

 

 

NAME

 

 

 

 

 

 

 

 

 

 

 

(COFFEE NAME)

NOT SAVED

Page 19

41343 080108

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Phone 217 529-6601 FAX 217 Single GPR DBC-DVBUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Programming SwitchesBrew Lockout Service TOOLS/TEST OutputsProgramming Lockout Switch mounted on main control board ScreenRecipes Using a Smart Funnel and a G9-2T DBC or MHG GrinderNot using a Smart Funnel and/or a G9-2T DBC or MHG Grinder Recipe Programing MethodsContinue to a LevelTo a ContinueContinue to G Continue to F Programming FunctionsContinue to D Continues to LReturn to B Byps OZ/M XX.X Spray Head CAL? Done YES Procedure for modifying units of measure Units Setting Units of MeasureProcedure for setting warmer control Procedure for setting auto warm shut offTIME? Main Screen Freshness TimeNEW Recipe ? Enable EnergysavrSET NEW Recipe Procedure for Setting the RecipeThis function allows the operator to set Brew Sizes DONE? SET NEW RecipeDone Being programmed modified along with Setup CompleteSET NEW Recipes Procedure to program the coffee nameReview RECIPES? No YES To exit, press Next until the display reads That Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee FavorsProcedure for reviewing recipes Review RecipesBatches DONE? No YES Brew OZ Setting or Adjusting Brew VOL- UmesBypass Modifying pulse brew SET Pulse BrewSET Pulse Brew DONE? Procedure to set pulse brew by exampleSET Pulse Brew by Example Container READY?TIMES? SET Pulse Brew Enter TimesTo the Main Screen Batches DONE? SET PreinfusionReview Recipes screen Procedure to modify drip timesSetup Complete Units as wellSET Temp Enable ADS?Procedure to Enable/Disable Ads Procedure to set brew temperatureRefill Range 20 to Procedure to set ready temperatureSpray OZ/M Spray OZ/M Single Brewers Procedure to adjust the flow rate settingSpray OZ/M Dual Brewers Bypass OZ/M Dual Brewers Bypass OZ/M Single BrewersCalibrate Flow ? Calibrate FlowBrate Bypass .. Press Brew to Start Procedures to calibrate the bypass flow rateBrew Counters Procedures to view/reset the brew countersFunnel Detect Service ToolsBrewers Programming FunctionsPress Next to return to Test Outputs Service ToolsProcedure to test switches Left Brew Valve on Dual brewersFrequency Service Tools Procedures to test coil frequencyScreen Factory Defaults Procedure to set factory defaults

41343 specifications

The Bunn 41343 is a highly efficient commercial coffee maker designed to meet the demands of busy coffee shops, restaurants, and offices. This model exemplifies Bunn's long-standing reputation for producing reliable brewing equipment that delivers consistent and quality coffee.

One of the standout features of the Bunn 41343 is its fast brewing capability. It can brew up to 3.8 gallons of coffee per hour, allowing establishments to keep pace with high customer demand. This is particularly beneficial during peak hours, ensuring that fresh coffee is always available. The design includes a stainless steel brew funnel that helps maintain thermal stability and ensures even extraction of coffee grounds.

The Bunn 41343 also incorporates advanced brewing technologies. It uses a unique spray-head design that evenly disperses hot water over the coffee grounds. This results in optimal flavor extraction and a rich, aromatic cup of coffee. The machine operates at a precise water temperature, which typically ranges from 195°F to 205°F, further enhancing the brewing process.

The brewer is equipped with a large internal hot water tank that maintains an optimal water temperature, ensuring that hot water is always available for brewing. This thermal retention system minimizes wait times and improves overall efficiency in environments where speed is crucial.

In terms of usability, the Bunn 41343 is designed with an intuitive interface that allows for easy operation. It features simple controls and clear indicators that help ensure consistent brewing results. The machine also comes with a built-in cleaning cycle that simplifies maintenance, allowing operators to keep it in top condition with minimal effort.

In terms of construction, the Bunn 41343 is built with durability in mind. The heavy-duty stainless steel exterior not only enhances its longevity but also gives it a professional appearance suitable for any commercial setting. Additionally, this model is designed to accommodate various cup sizes, making it versatile for different customer preferences.

In conclusion, the Bunn 41343 stands out as a robust commercial coffee maker that combines fast brewing capabilities with advanced brewing technologies. Its user-friendly design and durable construction make it an ideal choice for any coffee-centric business seeking quality and efficiency. Whether brewers are aiming to satisfy a morning rush or a steady afternoon crowd, the Bunn 41343 delivers with consistent performance and exceptional coffee flavor.
Top Page Image Contents