Bunn 41343 manual Screen, Service TOOLS/TEST Outputs, Brew Lockout

Page 6

PROGRAMMING THE BREWER

The programming of the brewer is divided into two levels. There is one function in Level 1. All other functions are accessed in Level 2.

The following function screens are in order of appearance. Each screen will have instructions on how to access, and the procedures to program the various functions of the brewer.

IMPORTANT PROGRAMMING NOTES

- READ CAREFULLY -

To exit the programming mode at any time, press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel. The display will return to the MAIN SCREEN.

If none of the five programming switches are pressed within one minute during the setup of the brewer, the programming of the function screen that is being set will be exited and the display will return to the MAIN

SCREEN.

Always remember to place a container and funnel under the sprayhead(s) when operating the brewer during the set-up of PULSE BREW - SET BY EXAMPLE, CALIBRATE FLOW and testing the brew and bypass valves in

SERVICE TOOLS/TEST OUTPUTS.

MAIN SCREEN

PROGRAM FUNCTIONS - LEVEL 1

 

BREW LOCKOUT

READY TO BREW WATER TEMP: 200°

This function allows the operator to prevent or allow brewing if the water temperature is less than the set READY temperature.

To access this function screen press and hold the ® symbol. Release the ® when the display reads:

P3070

This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water in the tank reaches the correct set temperature, the display will change from HEATING to READY TO BREW.

PROGRAMMING LOCKOUT SWITCH (mounted on main control board)

This switch can be set to prevent access to the programming levels of the brewer. Once all the cor- rect brew settings are programmed, the operator can set the switch to the "DISABLE" position to prohibit anyone from changing the settings.

 

PROGRAM

ENABLE

DISABLE

PROGRAMMING

SWITCH

P2424

BREW LOCKOUT?

NO DONE YES

Press here

Press here

Press here

for NO

for DONE

for YES

The YES or NO should be flashing. Select YES to prevent brewing if the water temperature is below the set READY temperature. Select NO to permit brewing at any water temperature.

When finished, press and release DONE. This will exit this function screen and return to the MAIN SCREEN on the display.

Page 6

41343 080108

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Single GPR DBC-DV Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Switches ProgrammingScreen Service TOOLS/TEST OutputsProgramming Lockout Switch mounted on main control board Brew LockoutRecipe Programing Methods Using a Smart Funnel and a G9-2T DBC or MHG GrinderNot using a Smart Funnel and/or a G9-2T DBC or MHG Grinder RecipesContinue LevelTo a Continue to aProgramming Functions Continue to G Continue to FContinues to L Continue to DReturn to B Byps OZ/M XX.X Spray Head CAL? Done YES Units Setting Units of Measure Procedure for modifying units of measureProcedure for setting auto warm shut off Procedure for setting warmer controlTIME? Freshness Time Main ScreenEnable Energysavr NEW Recipe ?Procedure for Setting the Recipe SET NEW RecipeThis function allows the operator to set Brew SET NEW Recipe Sizes DONE?Being programmed modified along with Setup Complete DoneProcedure to program the coffee name SET NEW RecipesReview RECIPES? No YES Review Recipes Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee FavorsProcedure for reviewing recipes To exit, press Next until the display reads ThatBrew OZ Setting or Adjusting Brew VOL- Umes Batches DONE? No YESBypass SET Pulse Brew Modifying pulse brewSET Pulse Brew Container READY? Procedure to set pulse brew by exampleSET Pulse Brew by Example DONE?SET Pulse Brew Enter Times TIMES?To the Main Screen SET Preinfusion Batches DONE?Units as well Procedure to modify drip timesSetup Complete Review Recipes screenProcedure to set brew temperature Enable ADS?Procedure to Enable/Disable Ads SET TempProcedure to set ready temperature Refill Range 20 toSpray OZ/M Procedure to adjust the flow rate setting Spray OZ/M Single BrewersSpray OZ/M Dual Brewers Bypass OZ/M Single Brewers Bypass OZ/M Dual BrewersCalibrate Flow Calibrate Flow ?Procedures to calibrate the bypass flow rate Brate Bypass .. Press Brew to StartProcedures to view/reset the brew counters Brew CountersService Tools Funnel DetectProgramming Functions BrewersLeft Brew Valve on Dual brewers Service ToolsProcedure to test switches Press Next to return to Test OutputsProcedure to set factory defaults Service Tools Procedures to test coil frequencyScreen Factory Defaults Frequency

41343 specifications

The Bunn 41343 is a highly efficient commercial coffee maker designed to meet the demands of busy coffee shops, restaurants, and offices. This model exemplifies Bunn's long-standing reputation for producing reliable brewing equipment that delivers consistent and quality coffee.

One of the standout features of the Bunn 41343 is its fast brewing capability. It can brew up to 3.8 gallons of coffee per hour, allowing establishments to keep pace with high customer demand. This is particularly beneficial during peak hours, ensuring that fresh coffee is always available. The design includes a stainless steel brew funnel that helps maintain thermal stability and ensures even extraction of coffee grounds.

The Bunn 41343 also incorporates advanced brewing technologies. It uses a unique spray-head design that evenly disperses hot water over the coffee grounds. This results in optimal flavor extraction and a rich, aromatic cup of coffee. The machine operates at a precise water temperature, which typically ranges from 195°F to 205°F, further enhancing the brewing process.

The brewer is equipped with a large internal hot water tank that maintains an optimal water temperature, ensuring that hot water is always available for brewing. This thermal retention system minimizes wait times and improves overall efficiency in environments where speed is crucial.

In terms of usability, the Bunn 41343 is designed with an intuitive interface that allows for easy operation. It features simple controls and clear indicators that help ensure consistent brewing results. The machine also comes with a built-in cleaning cycle that simplifies maintenance, allowing operators to keep it in top condition with minimal effort.

In terms of construction, the Bunn 41343 is built with durability in mind. The heavy-duty stainless steel exterior not only enhances its longevity but also gives it a professional appearance suitable for any commercial setting. Additionally, this model is designed to accommodate various cup sizes, making it versatile for different customer preferences.

In conclusion, the Bunn 41343 stands out as a robust commercial coffee maker that combines fast brewing capabilities with advanced brewing technologies. Its user-friendly design and durable construction make it an ideal choice for any coffee-centric business seeking quality and efficiency. Whether brewers are aiming to satisfy a morning rush or a steady afternoon crowd, the Bunn 41343 delivers with consistent performance and exceptional coffee flavor.
Top Page Image Contents