Bunn 41343 manual SET Pulse Brew, Modifying pulse brew

Page 24

PROGRAMMING FUNCTIONS - (cont.)

SET PULSE BREW:

This function allows the operator to program the brewer to "pulse” the sprayhead flow on and off con- tinually during a brew cycle (start and stop the flow of water out of the sprayhead). This feature allows the ability to “fine-tune” the brewer for specific flavor profiles. Pulse brewing can be set up for any and all batches.

INITIAL SPRAY

ON-

ON-

 

ON-

TIME

TIME

 

TIME ALTERNATES UNTIL

 

 

 

 

 

 

BREW CYCLE IS

OFF-

OFF-

 

OFF-

COMPLETED

 

 

TIME

TIME

 

TIME

 

P2293

a)1st ON TIME - This time is the duration from when the BREW switch is pressed to when the desired water level in the funnel is reached. (Soaking the grounds)

b)OFF-TIME - This time is the duration from when the water in the funnel reaches the desired ON TIME level to when it drains out of the funnel to a desired lower level.

c)LAST ON-TIME- This time is the duration from when the water in the funnel drains down to the lower level to when it fills the funnel to a desired higher level. (Soaking the grounds).

Modifying pulse brew:

Range: 1st on time - off to 4 minutes Off time - off to 4 minutes

Last on time - Preinfusion to 4 minutes

NOTE: If the brewer is already in the SET PULSE BREW screen, it is not necessary to follow steps 1 through 8 in this section, but proceed directly to step 9.

1.Press and hold the upper right hidden switch (®) until the display reads UNITS. Release the switch, then press and release the switch until the display reads REVIEW RECIPES.

2.Press YES to proceed. The display should now read:

NO NAME, along with MODIFY, SHOW and NEXT (SINGLE brewers)

 

 

REVIEW RECIPES?

 

 

NO

YES

EXIT TO

 

 

 

NEXT FUNCTION

SINGLE

DUAL

SCREEN

 

 

 

BREWERS

BREWERS

 

NO-NAME

NO-NAME LEFT

MODIFY SHOW NEXT

MODIFY SHOW NEXT

These three times can be set two different ways. The first is by observing the flow of water for on and off times. This is accomplished by utilizing the SET BY EXAMPLE screen and following the subsequent steps under that function.

The other allows the actual times to be entered for each of the settings. This is done by utilizing the ENTER TIMES screen and following the subsequent steps under that function.

Either of these methods can be used to set the pulse brew for each batch.

BREW OZ. XX.X (-) DONE (+)

3 BATCHES DONE?

NO YES

%BYPASSS XX.X (-) DONE (+)

ADVANCES TO ALL OTHER

COFFEE NAMES PROGRAMMED

IN THE BREWER"S MEMORY

(COFFEE NAME)

MODIFY SHOW NEXT

WHEN THE LAST COFFEE

NAME IN BREWER'S MEMORY

IS DISPLAYED, PRESSING NEXT WILL EXIT AND THE DISPLAY WILL THEN READ:

3 BATCHES DONE?

NO

YES

SET PULSE BREW?

NO

YES

Page 24

THAT WAS THE

LAST RECIPE

SEE PULSE BREW SETUP-

(SET BY EXAMPLE)

41343 080108

Image 24
Contents Single GPR DBC-DV Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Switches ProgrammingService TOOLS/TEST Outputs Programming Lockout Switch mounted on main control boardScreen Brew LockoutUsing a Smart Funnel and a G9-2T DBC or MHG Grinder Not using a Smart Funnel and/or a G9-2T DBC or MHG GrinderRecipe Programing Methods RecipesLevel To aContinue Continue to aProgramming Functions Continue to G Continue to FContinues to L Continue to DReturn to B Byps OZ/M XX.X Spray Head CAL? Done YES Units Setting Units of Measure Procedure for modifying units of measureProcedure for setting auto warm shut off Procedure for setting warmer controlTIME? Freshness Time Main ScreenEnable Energysavr NEW Recipe ?Procedure for Setting the Recipe SET NEW RecipeThis function allows the operator to set Brew SET NEW Recipe Sizes DONE?Being programmed modified along with Setup Complete DoneProcedure to program the coffee name SET NEW RecipesReview RECIPES? No YES Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee Favors Procedure for reviewing recipesReview Recipes To exit, press Next until the display reads ThatBrew OZ Setting or Adjusting Brew VOL- Umes Batches DONE? No YESBypass SET Pulse Brew Modifying pulse brewSET Pulse Brew Procedure to set pulse brew by example SET Pulse Brew by ExampleContainer READY? DONE?SET Pulse Brew Enter Times TIMES?To the Main Screen SET Preinfusion Batches DONE?Procedure to modify drip times Setup CompleteUnits as well Review Recipes screenEnable ADS? Procedure to Enable/Disable AdsProcedure to set brew temperature SET TempProcedure to set ready temperature Refill Range 20 toSpray OZ/M Procedure to adjust the flow rate setting Spray OZ/M Single BrewersSpray OZ/M Dual Brewers Bypass OZ/M Single Brewers Bypass OZ/M Dual BrewersCalibrate Flow Calibrate Flow ?Procedures to calibrate the bypass flow rate Brate Bypass .. Press Brew to StartProcedures to view/reset the brew counters Brew CountersService Tools Funnel DetectProgramming Functions BrewersService Tools Procedure to test switchesLeft Brew Valve on Dual brewers Press Next to return to Test OutputsService Tools Procedures to test coil frequency Screen Factory DefaultsProcedure to set factory defaults Frequency

41343 specifications

The Bunn 41343 is a highly efficient commercial coffee maker designed to meet the demands of busy coffee shops, restaurants, and offices. This model exemplifies Bunn's long-standing reputation for producing reliable brewing equipment that delivers consistent and quality coffee.

One of the standout features of the Bunn 41343 is its fast brewing capability. It can brew up to 3.8 gallons of coffee per hour, allowing establishments to keep pace with high customer demand. This is particularly beneficial during peak hours, ensuring that fresh coffee is always available. The design includes a stainless steel brew funnel that helps maintain thermal stability and ensures even extraction of coffee grounds.

The Bunn 41343 also incorporates advanced brewing technologies. It uses a unique spray-head design that evenly disperses hot water over the coffee grounds. This results in optimal flavor extraction and a rich, aromatic cup of coffee. The machine operates at a precise water temperature, which typically ranges from 195°F to 205°F, further enhancing the brewing process.

The brewer is equipped with a large internal hot water tank that maintains an optimal water temperature, ensuring that hot water is always available for brewing. This thermal retention system minimizes wait times and improves overall efficiency in environments where speed is crucial.

In terms of usability, the Bunn 41343 is designed with an intuitive interface that allows for easy operation. It features simple controls and clear indicators that help ensure consistent brewing results. The machine also comes with a built-in cleaning cycle that simplifies maintenance, allowing operators to keep it in top condition with minimal effort.

In terms of construction, the Bunn 41343 is built with durability in mind. The heavy-duty stainless steel exterior not only enhances its longevity but also gives it a professional appearance suitable for any commercial setting. Additionally, this model is designed to accommodate various cup sizes, making it versatile for different customer preferences.

In conclusion, the Bunn 41343 stands out as a robust commercial coffee maker that combines fast brewing capabilities with advanced brewing technologies. Its user-friendly design and durable construction make it an ideal choice for any coffee-centric business seeking quality and efficiency. Whether brewers are aiming to satisfy a morning rush or a steady afternoon crowd, the Bunn 41343 delivers with consistent performance and exceptional coffee flavor.