Bunn 41343 manual SET NEW Recipe, Sizes DONE?

Page 17
P2417
18. To SET PREINFUSION press YES in the SET PRE- INFUSION screen to proceed. The display should now read ON TIME and a batch light will be blink- ing.
19. Using (-)and (+), set the amount of time the brew water will initially presoak the grounds for that particular batch size.
20. When finished, press another batch size and repeat until all three batch sizes are set.
21. When finished, press DONE. The display should now read OFF TIME and a batch light will be blink- ing.
22. Using (-)and (+), set the amount of time the brew cycle will delay (after the presoak cycle shuts off) before resuming brewing.
23. When finished, press another batch size and repeat until all three batch sizes are set.

PROGRAMMING THE BREWER (cont.)

SET NEW RECIPE (cont.)

8.Using (-)and (+), set the amount of brew water, in ounces, to be dispensed for that particular batch size.

9.When finished, press another batch size and re- peat step 8 for that size. Continue setting all batch sizes.

10.When finished setting all batch sizes, press and release DONE. The display should read 3 BATCH

SIZES DONE?

11.If the three batch sizes are not correct, press and release NO to return to the BREW OUNCES setup screen and repeat steps 8 through 10. If the three batch sizes are correct, press YES. This will advance to the % BYPASS function. (Refer to % BYPASS for description).

% BYPASS XX.X

(-)

DONE

(+)

3 BATCHES DONE?

NO

 

YES

SET PULSE BREW?

NO YES

P2416

12.Using (-)and (+) set the amount of bypass water (percentage) to be dispensed around the grounds for that particular batch size.

13.When finished, press another batch size and repeat step 12 for each batch to be set.

14.When finished setting each batch size, press DONE. The display should read 3 BATCHES DONE?

15.If the three batch sizes are not correct, press and release NO to return to the % BYPASS setup screen and repeat steps 12 through 15. If they are correct, press YES. This will advance to SET PULSE BREW. (Refer to SET PULSE BREW for description).

16.To SET PULSE BREW, if setting pulse brew BY EXAMPLE (brewing into a funnel) press YES and proceed with the setup instructions for SETTING PULSE BREW - BY EXAMPLE.

17.If setting pulse brew by ENTER TIMES (enter- ing known times) press NO. The display should read ENTER TIMES. Press and release YES and

Page 17

proceed with the setup instructions for SETTING PULSE BREW - ENTER TIMES. SET DRIP TIME. (Refer to SET DRIP TIME for description). After SET PULSE BREW has been accomplished, the next function will be SET PREINFUSION. (Refer to SET PREINFUSION function for description.

SET PREINFUSION?

NO

 

YES

ADVANCES

 

 

TO NEXT

 

 

FUNCTION

 

 

ON TIME X:XX

(-)

DONE

(+)

OFF TIME X:XX

(-)

DONE

(+)

ON

 

OFF

X:XX

 

X:XX

 

5 SEC. DELAY

 

3 BATCHES DONE?

NO

 

YES

DRIP TIME X:XX

(-)

DONE

(+)

41343 080108

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Phone 217 529-6601 FAX 217 Single GPR DBC-DVBUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Programming SwitchesProgramming Lockout Switch mounted on main control board Service TOOLS/TEST OutputsScreen Brew LockoutNot using a Smart Funnel and/or a G9-2T DBC or MHG Grinder Using a Smart Funnel and a G9-2T DBC or MHG GrinderRecipe Programing Methods RecipesTo a LevelContinue Continue to aContinue to G Continue to F Programming FunctionsReturn to B Continues to LContinue to D Byps OZ/M XX.X Spray Head CAL? Done YES Procedure for modifying units of measure Units Setting Units of MeasureTIME? Procedure for setting auto warm shut offProcedure for setting warmer control Main Screen Freshness TimeNEW Recipe ? Enable EnergysavrThis function allows the operator to set Brew Procedure for Setting the RecipeSET NEW Recipe Sizes DONE? SET NEW RecipeDone Being programmed modified along with Setup CompleteSET NEW Recipes Procedure to program the coffee nameReview RECIPES? No YES Procedure for reviewing recipes Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee FavorsReview Recipes To exit, press Next until the display reads ThatBatches DONE? No YES Brew OZ Setting or Adjusting Brew VOL- UmesBypass Modifying pulse brew SET Pulse BrewSET Pulse Brew SET Pulse Brew by Example Procedure to set pulse brew by exampleContainer READY? DONE?To the Main Screen SET Pulse Brew Enter TimesTIMES? Batches DONE? SET PreinfusionSetup Complete Procedure to modify drip timesUnits as well Review Recipes screenProcedure to Enable/Disable Ads Enable ADS?Procedure to set brew temperature SET TempSpray OZ/M Procedure to set ready temperatureRefill Range 20 to Spray OZ/M Dual Brewers Procedure to adjust the flow rate settingSpray OZ/M Single Brewers Bypass OZ/M Dual Brewers Bypass OZ/M Single BrewersCalibrate Flow ? Calibrate FlowBrate Bypass .. Press Brew to Start Procedures to calibrate the bypass flow rateBrew Counters Procedures to view/reset the brew countersFunnel Detect Service ToolsBrewers Programming FunctionsProcedure to test switches Service ToolsLeft Brew Valve on Dual brewers Press Next to return to Test OutputsScreen Factory Defaults Service Tools Procedures to test coil frequencyProcedure to set factory defaults Frequency

41343 specifications

The Bunn 41343 is a highly efficient commercial coffee maker designed to meet the demands of busy coffee shops, restaurants, and offices. This model exemplifies Bunn's long-standing reputation for producing reliable brewing equipment that delivers consistent and quality coffee.

One of the standout features of the Bunn 41343 is its fast brewing capability. It can brew up to 3.8 gallons of coffee per hour, allowing establishments to keep pace with high customer demand. This is particularly beneficial during peak hours, ensuring that fresh coffee is always available. The design includes a stainless steel brew funnel that helps maintain thermal stability and ensures even extraction of coffee grounds.

The Bunn 41343 also incorporates advanced brewing technologies. It uses a unique spray-head design that evenly disperses hot water over the coffee grounds. This results in optimal flavor extraction and a rich, aromatic cup of coffee. The machine operates at a precise water temperature, which typically ranges from 195°F to 205°F, further enhancing the brewing process.

The brewer is equipped with a large internal hot water tank that maintains an optimal water temperature, ensuring that hot water is always available for brewing. This thermal retention system minimizes wait times and improves overall efficiency in environments where speed is crucial.

In terms of usability, the Bunn 41343 is designed with an intuitive interface that allows for easy operation. It features simple controls and clear indicators that help ensure consistent brewing results. The machine also comes with a built-in cleaning cycle that simplifies maintenance, allowing operators to keep it in top condition with minimal effort.

In terms of construction, the Bunn 41343 is built with durability in mind. The heavy-duty stainless steel exterior not only enhances its longevity but also gives it a professional appearance suitable for any commercial setting. Additionally, this model is designed to accommodate various cup sizes, making it versatile for different customer preferences.

In conclusion, the Bunn 41343 stands out as a robust commercial coffee maker that combines fast brewing capabilities with advanced brewing technologies. Its user-friendly design and durable construction make it an ideal choice for any coffee-centric business seeking quality and efficiency. Whether brewers are aiming to satisfy a morning rush or a steady afternoon crowd, the Bunn 41343 delivers with consistent performance and exceptional coffee flavor.
Top Page Image Contents