CDA RV 1060 Safety Hints, Cleaning the Hob, Tool take extra care to avoid damaging the seal at

Page 12

12

Safety Hints:

Before you switch the hob on, make sure you know which knob controls the required cooking plate. We advise you to set the pan over the cooking plate before switching it on. Remove the pan after you have switched the cooking plate off.

Do not use pots and pans with rough bases (pay attention to cookware made of cast-iron). Rough bases can damage (scratch) the glass surface of the hob.

Make sure that the bottom of the pan is dry and clean.

Pots with aluminium bottoms may leave silver streaks or spots on the hob.

Do not leave wet or damp lids on the hob.

The glass-ceramic surface and pans must be clean. Carefully remove any food debris (especially containing sugar), dirt etc. with the aid of a cleansing agent.

Pan handles should never stand out beyond the kitchen worktop, as there is a great danger of knocking the pan over.

This will also ensure that children cannot reach them.

Do not use the hob if the glass surface is broken or cracked in any way. Please disconnect the cooker from the mains and contact the after-sales service.

Do not lean over the cooking plate when in use.

Do not lay cooking foil or plastic materials on the ceramic surface when it is hot.

Do not use the glass surface for storage.

Remember that the surface remains hot for a long time (about 30 min.) after the cooking plate has been switched off.

Follow the cleaning instructions carefully.

Cleaning the Hob

Before you begin cleaning make sure that the appliance is switched off.

Remove spillages and other types of incrustations.

Dust or food particles can be removed with a damp cloth.

If you use a detergent, please make sure that it is not abrasive or scouring. Abrasive or scouring powders

can damage the glass surface of the hob.

 

All traces of the cleaner must be removed with a damp cloth.

 

Do not put articles on the hob which can melt: i.e plastic,

 

aluminium foil, sugar, sugar syrup mixtures etc.

 

If any of these products items have melted on the ceramic surface,

 

you should remove it immediately (when the surface is still hot)

 

by using a scraper to avoid any permanent damage to the surface

 

of the hob. (Available under part No. 103138).

 

Avoid using a knife or other sharp utensils since these can damage

 

the ceramic.

 

Do not use steel wool or an abrasive sponge which could scratch

 

the surface permanently.

 

ATTENTION: MOST IMPORTANT!

 

If cleaning the glass ceramic hob using a special scraper

Fig. 12

tool take extra care to avoid damaging the seal at the

 

edges of the glass ceramic surface.

 

Image 12
Contents Twin Cavity Ceramic Cooker Appliance Information Declaration of CE ConformityFeatures and Technical Data Vitroceramic Cooking HobConventional Oven Main OvenControl Panel Controls DescriptionPilot Lamps Clock and Timer with Touch-Control Keys Illuminated SymbolsKeys Setting the Clock Using the TimerSetting the Timer Volume Touch-Control KeysAutomatic Cooking How to Use the Vitroceramic Hob Important NoteCircuit Radiant Zones To return to using only the inner zone of the double Double and Oval Radiant ZonesCooking Hints Residual Heat Indicators Cooking HintsDeep Fat Frying Safety Hints Cleaning the HobTool take extra care to avoid damaging the seal at Edges of the glass ceramic surfaceHow to Use the Multifunction Main Oven General FeaturesOperating Principles Thermostat Knob fig Function Selector knob figOven Light Traditional Convection CookingGrilling Defrosting Frozen FoodsHot Air Cooking Ventilated Grill Cooking Convection Cooking with VentilationCooking Advice SterilizationRegeneration Simultaneous Cooking of Different FoodsRoasting Use of the GrillHow to Use the Conventional Oven Traditional Grilling Rotisserie Use of the RotisserieOven is equipped with a rotisserie Using the Special Shelf as a Dish Rack Using the Special Rack for Normal CookingUse of Special Dish Rack For Your Safety Do’s and do not’sImportant Notes Care and Maintenance SpillageEnamelled Parts Replacing the Halogen Oven Lights DrawerInside of Ovens Assembling and Dismantling of the Side Runner FramesDoors Assembly Oven DoorsRemoving the Oven Doors Over Doors Cleaning The Panes Of Glass Removing the Inner PaneReassembling the Inner Pane For the Installer LocationAssembling the Backguard Levelling the CookerPage Stability Bracket Wall fixing Floor fixingElectrical Installation For Your Safety Please Read the Following InformationConnecting the Mains Cable Feeder Cable Section Type H05RR-F or H05VV-FGuarantee Appliance ServicingLimit of Cover Contact Telephone NumbersCod ß2