APC ACRP501, ACRP502, ACRP500, ACRP102 manual Chilled Water Only Alarms, Air-cooled Only Alarms

Page 12

Alarms

The microprocessor controller shall activate a visible and audible alarm in the following occurrences:

•Cool Fail

•Rack inlet temperature violation

•Rack inlet temperature sensor fault

•Air filter clogged

•Air filter run hours exceeded

•Filter DP sensor failure

•Supply air sensor fault

•Return air sensor fault

•Supply air high temperature violation

•Return air high temperature violation

•Fan fault

•Fan run hours exceeded

•Water detection fault

•Condensate pump fault

•Condensate run hours exceeded

•Humidifier water conductivity high violation

•Humidifier fault tolerance exceeded

•Humidifier low water

•Humidifier excessive output reduction

•Humidifier drain fault

•Humidifier cylinder full

•Humidifier replace cylinder

•Humidifier RS485 communication fault

•Humidifier run hours violation

•Humidity high/low violation

•Supply humidity sensor fault

•Return humidity sensor fault

•Heater fault

•Heater run hours exceeded

•Heater interlock shutdown

•Group communication fault

•Internal communication fault

•A-link isolation relay fault

•External communication fault

•Input contact fault

•Invalid supply setpoint

•Idle mode active

Chilled Water Only Alarms

•Coil fluid valve actuator fault

•Fluid flow fault

•Entering fluid temperature high violation

•Entering fluid temperature sensor fault

•Leaving fluid temperature sensor fault

•Power source failure

•Fluid calibration

Air-cooled Only Alarms

•High discharge pressure

•Low suction pressure

•High suction pressure

•Compressor drive failure

•Compressor drive warning

•Compressor run hours violation

•Compressor drive RS485 communication fault

•Excessive compressor cycling

•Air flow decreased while compressor off

•Suction pressure sensor failure

•Discharge pressure sensor failure

•High pressure switch active

•Fan speed decreased to avoid high pressure (event only)

•Compressor speed decreased to avoid high pressure (event only)

•Compressor high pressure

•Oil return pump active

8

InRow RP Technical Data Manual

Page 11 Page 13
Image 12
Page 11 Page 13
Contents InRow RP American Power Conversion Legal Disclaimer Contents InRow RP Models Overview Scalable Solution for Critical Environments InRow AdvantagesScalable for High Density Hot Aisle Containment System Standard Features Remote Temperature Sensors Dual Position Float Condensate ManagementNetwork Management Card Bay Kit InRow RP NetShelter SXOptional Features Microprocessor Controller Alarms Chilled Water Only AlarmsAir-cooled Only Alarms InRow RP Models Chilled Water Interior Components front of unit Chilled Water Interior Components back of unit Air-cooled Interior Components front of unit Air-cooled Interior Components back of unit Chilled Water and Air-cooled User Interface Connections BMS GNDChilled Water Electrical Panel Air-cooled Electrical Panel Performance Specifications Chilled Water Performance Specifications 5.5C 42F EWTChilled Water Performance Specifications 7.2C 45F EWT GPMChilled Water Performance Specifications 8.9C 48F EWT 29.4C DB, 18.1C WBChilled Water Performance Specifications 10C 50F EWT Chilled Water Performance Specifications 12.8C 55F EWT Chilled Water Performance Specifications 15.5C 60F EWT Chilled Water Data General Modulating ValvesAir-cooled Performance Specifications Glycol Correction FactorsAltitude Correction Factors for InRow Products Air-cooled Data General Sound Performance Data Electrical DataDimensional Data InRow RP Assembled ModuleSX to VX Height Adapter SX to 48U SX Height AdapterChilled Water Piping Diagram Piping and Mechanical ConnectionsTop Chilled Water Piping Access top view FRONT-COLD AisleBottom Chilled Water Piping Access bottom view, looking up Air-cooled Piping Diagram Air-cooled Piping Access top Air-cooled Piping Access bottom view, looking up Air-Cooled Condensers Mechanical DataACCD75201 and ACCD75204 ACCD75202 and ACCD75205 ACCD75203 and ACCD75206Air-cooled Condenser Features ACCD75207ACCD75208 and ACCD75209 Guide Specifications Part 1 GeneralVariable Speed FAN Assembly InRow RP Technical Data Manual Network Management Card Condensate Pump Selectable TOP or Bottom Piping AIR-COOLED only Guidelines for Installation Page APC Worldwide Customer Support 990-2469E-001 2009
Related manuals
Manual 82 pages 30.8 Kb

ACRP502, ACRP500, ACRP501, ACRP102, ACRP101 specifications

The APC ACRP series, consisting of models ACRP100, ACRP101, ACRP102, ACRP501, and ACRP500, represents a significant innovation in power distribution and protection. These compact, reliable, and efficient solutions are designed specifically for critical applications in data centers, industrial environments, and commercial facilities.

The ACRP100 is the entry-level model, providing essential features for basic power monitoring and control. It incorporates advanced metering capabilities, enabling users to monitor voltage, current, and power consumption in real-time. The ACRP100's user-friendly interface allows for easy navigation, making it an ideal choice for small to medium-sized installations that require fundamental power management.

Stepping up, the ACRP101 enhances functionality with added remote monitoring capabilities. This model introduces smart connectivity features, allowing users to access critical data from anywhere through a secure mobile application or web-based platform. With its ability to integrate seamlessly with other APC systems, the ACRP101 is tailored for environments seeking improved operational visibility and proactive maintenance.

The ACRP102 takes a further leap by integrating advanced predictive analytics. This model uses machine learning algorithms to analyze data trends, predicting potential failures before they occur. By minimizing downtime and optimizing maintenance schedules, the ACRP102 becomes a vital tool for organizations focused on reliability and efficiency.

In the higher-end range, the ACRP501 offers robust power management features, including enhanced surge protection and redundancy capabilities. This model is ideal for mission-critical operations where every second counts. It supports a wide range of input voltages and can manage multiple power sources concurrently, ensuring uninterrupted power supply in fluctuating conditions.

Lastly, the ACRP500 combines all the leading features of the series, focusing on scalability and flexibility. This model is engineered to adapt to evolving infrastructure needs, supporting modular configurations that can grow with the organization. Its extensive reporting functions and customizable dashboards provide clear insights into power usage and performance metrics, empowering facility managers to make informed decisions.

In summary, the APC ACRP series provides a comprehensive suite of solutions for power management, tailored to meet diverse operational needs. From basic monitoring with the ACRP100 to the predictive capabilities of the ACRP102 and the advanced functionalities of the ACRP500, these models collectively offer enhanced reliability, efficiency, and scalability while ensuring optimal protection for critical applications.
Top Page Image Contents