Russound CAV6.6-S2 instruction manual BUS Ready Sub-zone Connection

Page 35

A-BUS Ready Sub-zone Connection

A-BUS products can easily expand the CAV6.6 audio system by adding A-BUS Ready Sub-zones to the first four CAV6.6 zones. The A-BUS Ready Sub-zones are located on the back of the CAV6.6 at the bottom left corner. The A-BUS Ready Sub-zones are powered by a 24VDC power supply such as the A-PS.

Use an RJ-45 CAT-5 T568A configuration patch cable to connect the A-BUS Ready Sub-zone

INSTALLER

MAKING CONNECTIONS

port to an RJ-45 wall plate (optional) for a clean installation. Using the same T568A RJ-45 wiring configuration, attach CAT-5 from the RJ-45 wall plate to an A-BUS hub or amplified control mod- ule such as the A-KP2 keypad.

If using an A-BUS hub with the A-BUS Ready Sub- zone, the hub should be located near the CAV6.6 and wired directly instead of first going through the wall plate.

35

Image 35

Contents CAV6.6-S2 System Power Cord Notice for International Operation Important SafeguardsTable of Contents Reference Section Operation Component GuidesFavorites Product IntroductionCAV6.6 Controller-Front Panel UserComponent Guide Front A/V AUX Connections UNO-S2 Keypad-Front Panel Optional UNO-S1 Keypad-Front Panel Favorite 2 preset selections UNO-LRC1 Remote ControlUNO-S2 Keypad Main Power and Zone StatusOperation CAV6.6 ControllerUNO-S2 Keypad Button Functions Balance UNO-S2 User Menu Setting PreferencesFeature and Setting 1. Bass TrebleScrolls through the six audio source inputs Optional UNO-S1 Keypad Button FunctionsFrtAV Front A/V Aux In Enabled/Disabled Optional UNO-S1 User Menu Setting PreferencesFeature and Setting Party Party Mode Master or OffInstallation Menu Keypad InstallationFirmware Updates System Installation OverviewGetting Started InstallerSpeaker Wiring Wiring InstructionsKeypad Wiring CAT-5 Wire Color TypeComponent Guide CAV6.6 Controller-Front Panel CAV6.6 Controller-Rear Panel Installer +12VDC Data Rx RS-232 Data Tx RS-232GND UNO-S2 Keypad-Rear Panel Keypad Location UNO-S2 KEYPAD-INSTALLATIONCAT-5 Connection OS Update Port Jumper SettingUNO-S2 Keypad Connections Back Russound IR Receiver ConnectionMaking Connections UNO System Keypad Port ConnectionSource IR Connections Source Audio/Video Input ConnectionsSource Audio/Video Loop Output Connections Speaker Connections ACC IR Connection Zone Audio to Amp and Video Outputs BUS Ready Sub-zone Connection 12VDC 50mA Trigger Out 12VDC Trigger In/Out12VDC Home Theater Trigger Zone 12VDC Trigger Outputs Audio/Video 12VDC Page Trigger12VDC Page Trigger Out Installer Rnet Link In and Link Out Multiple Controllers Rnet Link In and Link Out RNET-enabled Components RS-232 Interface Programming Center Keypad Port Connection UNO-S2 Keypad Diagnostics Menu Requirements UNO-S2 Keypad Firmware Update ProcedureCAV6.6 Firmware Update Procedure System requirements for PC Power Tool PC Power Tool ProgrammingInitial Install Test System Programming Overview ProgrammingSystem Programming Overview cont’d Source Information Form Zone Information Form Macro Editor Form Menu Item Installation MenuProcedure FeatureSelected Learned IR Command TypeSource NUM Source NameZone NUM Basic Setup cont’dIi. Template TYP TType To build macros, see Macro Editor Key Config cont’dPrefix CMD Trim LevelHighest NUM Numeric TextSuffix CMD Numeric IR cont’dDevice Code KEY FunctionSave CHANGES? MacroMaster Enable Source Select Command cont’dSyson Enable Party EnableController ID CtlId Factory Init FInit Zone Setup cont’dEnable VolumePower on CMD OnCmd Power Management cont’dSense Delay Learn IR LrnIR Power OFF CMD OfCmdTest IR? Learn IR cont’dLearned SRC LEARN/DELETEBuild Date Macro Editor cont’d#CONTROLLERS Build TimeSource Setup Basic Setup Setup Menu Flow ChartsSource Setup Key Configuration Source Setup Source Names/Volume Trim Source Setup Numeric IR Source Setup Source Select Command/# of Sources Zone Setup Controller Setup Power Management Learn IR Macro Editor System Info IR Device Codes Sample ConfigurationsTechnical Specifications WarrantyDevice Codes for Video Acc IR CodesDevice Codes for TVs Device Codes for CableDevice Codes for Laser Disc Players Device Codes for SAT/DSSDevice Codes for VCRs Device Codes for CD Players Device Codes for DVD PlayersDevice Codes for Tuner/Amp Device Codes for Amp and Misc. AudioUNO-S1 UNO-S2 Source NamesTivo Six Zones and Six Sources Sample System ConfigurationSample System Configuration Rnet Link In and Link Out Integrate Multiple CAV6.6’sSample System Configuration Zone Keypad Expansion Sample System Configuration CAT-5 Connections Multi-Source Mode SwitchBUS Ready Sub-Zone Addition BUS HubSample System Configuration Zone Audio To Amp & Video Outputs Additional AmplificationSample System Configuration Front Left and Right Speakers Home TheaterSource Loop Outputs Sample System Configuration KEY Function UNO-S1 TV Hdtv KEY Codes TV HdtvSAP SAP, CC KEY Function UNO-S1 Cable KEY Codes CableSAP KEY Function UNO-S1 Video ACC KEY Codes Video ACCLanguage, MTS KEY Function UNO-S1 SAT/DSS KEY Codes SAT/DSSAlt/Audio,Lang.,CC KEY Function UNO-S1 VCR KEY Codes VCRMenu Back Clear Fav Channel FavCh KEY Function UNO-S1 Laser Disc KEY Codes Laser DiscSubtitle, CC KEY Function UNO-S1 DVD KEY Codes DVD109 KEY Function UNO-S1 Receiver KEY Codes ReceiverDVD, LD KEY Function UNO-S1 AMP/MISC Audio KEY Codes AMP/MISC AudioTAPE, MD KEY Function UNO-S1 KEY Codes CDInput Tape, MD KEY Function UNO-S1 Home Control KEY Codes Home ControlInput Source/Scene UNO-S2 Keypad Technical SpecificationCAV6.6 Controller/Amplifier Warranty & Repair