Cleveland Range 22CET3.1, 22CET6.1 Install the Legs, Packing Blocks Position and Level the 22CET

Page 12

C.Install the Legs

1.The legs must be used unless the 22CET is installed on a Cleveland Range stand.

2.In order to safely assemble the legs onto the 22CET without damage, follow this procedure:

a.Check that the feet are fully retracted into the legs. Do not tighten. The feet should easily screw in and out using fingers only.

b.Remove the four foam packing blocks from the upper packing assembly, and position them on a flat surface (e.g. the floor) as shown in Figure 3-1.

c.Center the steamer on the blocks as shown in Figure 3-1 and 3-2.

d.Screw the four legs into the mounting holes. All four legs must be used for proper installation of a 22CET.

e.Lift the 22CET off the blocks, and move it to its installed location.

f.Discard the foam packing blocks.

Figure 3-1

Figure 3-2

Top View Steamer on Foam

Front View Steamer on Foam Blocks

Packing Blocks

 

D.Position and Level the 22CET

1.Move the 22CET to its installed location.

2.Using a level, adjust the legs of the 22CET or the legs of the Cleveland Range stand until the 22CET is level front-to-back and side-to-side.

E.Install the KleanShield™

a.Never operate a SteamChef Steamer without a properly installed KleanShield.

b.To install the KleanShield:

1)Remove the slide pan racks.

2)Place the KleanShieldinto the steamer with the drain to the back of the cooking compartment and the pipe extension facing down.

3)Set the KleanShieldin place over the corresponding pipe extending out of the bottom of the steamer reservoir. See Figure 3-3.

4)Fit the pipe from the KleanShieldinto the corresponding pipe in the bottom of the steamer.

5)KleanShield™ legs must be flush against the bottom of the steamer. See Figure 3-4.

7

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation Manual Keep this Manual for Reference Cleveland Statement of Policies Page Installation Manual Product Information Product InformationProduct Information Plate General Information Laws, Codes, and RegulationsInspect for Shipping Damage SteamChef 3.1 Dimensions and Clearances Product ViewsSteamChef 6.1 Dimensions and Clearances Installation Select a LocationPage Install the Legs Install the KleanShieldPacking Blocks Position and Level the 22CET KleanShield Install the Rear Vent Clearance Minimum Typical Drain Connection SteamChef 3 ShownWater Supply Requirements and Installation Install the Water Supply Lines Installation RequirementsFilter Washer 110987 Shown Test Water Supply Lines 10 Cleveland Range Single Water Supply ArrangementElectric Power Supply Do not use a power cordElectrical Layout Electrical ConnectionsCompleted Startup Procedure Interior AccessoriesOperating Tests SteamChef 6.1 ShownDrain Rinse Inspection continue from Startup Procedure Page Page INSTALLER’S Troubleshooting Guide Operator’s Trouble Shooting GuideOn Next See Warning under To verify the steamersProper operation see Troubleshooting Notes

22CET6.1, 22CET3.1 specifications

The Cleveland Range 22CET3.1 and 22CET6.1 are exceptional cooking units designed for high-performance in commercial kitchens. These versatile countertop electric tilting braising pans are engineered to provide chefs with a reliable and efficient tool for a myriad of cooking tasks.

One of the standout features of the 22CET series is the ability to tilt, allowing for easy pouring and transferring of food. This innovative design not only saves time but also enhances safety by minimizing the risk of spills and burns. Equipped with an intuitive control panel, chefs can quickly adjust the temperature settings for precise cooking. The digital control panel also offers easy readability, ensuring that chefs can monitor cooking temperatures effectively.

The Cleveland Range 22CET3.1 has a 30-gallon capacity, while the 22CET6.1 boasts a larger 60-gallon capacity, catering to operations of different scales. Both models are constructed from high-quality stainless steel, ensuring durability and resistance to the rigors of a busy kitchen environment. The robust design also facilitates easy cleaning and maintenance, making them ideal for foodservice operations.

Incorporating advanced heating technologies, these braising pans feature a direct steam heating method which provides rapid temperature recovery. This feature is particularly beneficial for high-volume kitchens, allowing chefs to cook large quantities of food consistently and quickly. The even heat distribution ensures that food is cooked uniformly, reducing the chances of burning or uneven cooking.

Another notable characteristic of the Cleveland Range 22CET models is their ability to handle a variety of cooking methods, including steaming, braising, sautéing, and simmering. This versatility allows chefs to create a diverse menu, ranging from soups and stews to stir-fries and sauces.

Safety features are also prominent in the design of the Cleveland Range 22CET3.1 and 22CET6.1. The built-in safety thermostat and high-limit switch provide peace of mind by preventing overheating during operation. Furthermore, the cool-touch handle ensures that manipulating the tilting mechanism remains safe for the users.

In conclusion, the Cleveland Range 22CET3.1 and 22CET6.1 are powerful, reliable, and versatile cooking solutions for professional kitchens. Their combination of efficiency, safety, and ease of use positions them as essential tools for culinary professionals looking to elevate their cooking capabilities.
Top Page Image Contents